manualshive.com logo in svg

Danfoss EM-PMI540-T4000, Руководство пользователя

Поделиться
Скачать
Danfoss EM-PMI540-T4000 Скачать руководство пользователя страница 36

The amount of inverters depends on the electric machine and converter current ratings. See also the
relevant wiring diagrams.

For an electric machine with option DUAL (two connection boxes each containing one three-phase
system), the electrical connection principles from the inverters are shown in the Figure below.

Connection diagram for DUAL option

For an electric machine with option QUAD (four galvanically isolated three-phase systems), the electrical
connection principles from the inverters are shown in the Figure below.

Connection diagram for QUAD option

Cable gland assembly and power line connection

If you are not using the recommended cable lugs, select cable lugs that leave 10 mm gap

between each and every cable lug on the same connection plate.

The pictures are schematic, and the actual components can look different.

User Guide

EM-PMI540-T4000

Installation

 

36 | 

©

 Danfoss | April 2023

BC265857716810en-000202

Содержание EM-PMI540-T4000








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды