manualshive.com logo in svg

Danfoss EM-PMI540-T1500, Руководство пользователя

Поделиться
Скачать
Danfoss EM-PMI540-T1500 Скачать руководство пользователя страница 37

Foot mounting, optional

1

Foot mounting

2

Foot mounting attachment holes

Cooling connections

Make sure that cooling liquid runs freely into and out from the electric machine.

To prevent damage to the cooling connectors, refer to the documentation of the

manufacturer for the correct tightening torque of the cooling liquid nipples. 

When selecting cooling liquid nipples, choose nipples that can resist galvanic corrosion.

Connect the electric machine properly to the cooling circuit. Make sure that the coolant flow is equal or
higher than rated and the coolant temperature at the inlet of the machine cooling is lower or equal to the
rated temperature. For more information, see Chapter 

Recommended coolants

 and product data sheet.

Rated values can be found in the electric machine rating plate.

Aluminum frame water-cooled construction is only to be used with a closed fresh water circulation with
corrosive inhibitor described in the data sheet. The water cooling circuit connection is described in the
data sheet. Use only suitable and high-class connection parts and seals to connect the electric machine to
the water circuit. Check for possible leaks after the piping and joints have been connected.

Use only suitable and high-class connection parts and seals to connect the electric machine to the water
circuit. Check for possible leaks after the piping and joints have been connected.

It is recommended to use coolant connector equipped with o-ring seal or to use sealing washer (for
example Usit or Bonded seals) in the connection. In addition, it is recommended to use thread sealant

User Guide

EM-PMI540-T1500

Installation

 

©

 Danfoss | July 2021

BC265856800806en-000201 | 37

Содержание EM-PMI540-T1500













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды