Danfoss AK-CC55, Руководство пользователя, Страница: 55 / 64

Function Description Values Code Short name
Miscellaneous - Pri-
ority
Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
0=Disabled, 3=Low, 2=Medium, 1=High q33 q33 Misc Prio
Injection - Priority Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
0=Disabled, 3=Low, 2=Medium, 1=High q34 q34 Inject Prio
Control stopped -
Priority
Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
0=Disabled, 3=Low, 2=Medium, 1=High q35 q35 CtrlOFF Prio
Leak detection - Pri-
ority
Select the priority of the alarms associated to the
alarm group. Be aware - by selecting "Disable" the
alarms will not be shown on the display or be routed
to the alarm relay or to the network.
0=Disabled, 3=Low, 2=Medium, 1=High q36 q36 Leak Prio
Miscellaneous
Table 36: Miscellaneous
→
Access codes
Function Description Values Code Short name
Access code 3 Access code for local display o05 o05 Acc. code 3
Access code 2 Access code for local display o64 o64 Acc. code 2
Access code 1 Access code for local display P88 P88 Acc. code 1
Table 37: Miscellaneous
→
Network
Function Description Values Code Short name
Network status Quality of the network communication U45 U45 Comm. status
Network address Network address of the controller o03 o03 Unit addr.
Baudrate Communication speed of network 1=Auto, 2=9600 Baud, 3=19200 Baud, 4=38400 Baud x96 --- Bus baudrate
Parity and stop bit Select parity and stop bit of Modbus messages 0=None, 1=Even, 2=Odd x97 --- Parity bit
Table 38: Miscellaneous
→
Sensor adjustment
Function Description Values Code Short name
S2 Gas outlet A - Ad-
justment
Correction of sensor signal e.g. due to long sensor ca-
ble
r19 r19 Adjust S2
S3 Air ON evap. A -
Adjustment
Correction of sensor signal e.g. due to long sensor ca-
ble
r10 r10 Adjust S3
S4 Air OFF evap. A -
Adjustment
Correction of sensor signal e.g. due to long sensor ca-
ble
r09 r09 Adjust S4
S5 Evaporator A -
Adjustment
Correction of sensor signal e.g. due to long sensor ca-
ble
r11 r11 Adjust S5
Table 39: Miscellaneous
→
Factory reset
Function Description Values Code Short name
Make new factory With this command you save the controller’s actual
settings as a new basic setting (the earlier factory set-
tings are overwritten).
0=OFF, 1=ON o67 o67 Make factory
Reset to factory set-
tings
Command which will revert all controller settings to
factory values.
0=OFF, 1=ON z06 --- Reset factory
Advanced
Table 40: Advanced
→
Advanced injection control
Function Description Values Code Short name
Superheat ctrl.
mode A
Select how to control the superheat of the evapora-
tor. At adaptive control the superheat reference is
adapted automatically to give the best utilization of
the evaporator surface. At load based control the su-
perheat reference is increased at high loads
1=Adaptive, 2=Load based n21 n21 SH mode
Superheat close A Minimum superheat limit where the valve is closing x68 --- SH close
AFidentForce A Expert setting - contact Danfoss for further informa-
tion
x69 --- AFidentForce
Superheat Kp min A Min limit for amplification factor of PI controller ad-
justing the valve opening degree (expert setting)
x70 --- SH Kp min
Superheat Kp max A Max limit for amplification factor of PI controller ad-
justing the valve opening degree (expert setting)
x71 --- SH Kp max
© Danfoss | Climate Solutions | 2022.08 BC365212986197en-000201 | 55
AK-CC55 Compact