Danfoss 45 K2 Series страница 7 Скачать руководство пользователя

Страница: 7 / 40

Auxiliary pad

If a second pump is used, you must remove it. You don’t need to remove auxiliary pads to remove the
end cap.

1. Remove the plate cover screws (J130) and remove the cover plate (J110).
2. Remove the coupling (J140) and the pad seal (J120). If you have an auxiliary B pad, discard the O-ring

(J120). The pad seal for an auxiliary A pad is reusable if undamaged.

3. Remove the auxiliary pad screws (J100) with an 8 mm internal hex wrench and remove the adapter

(J085).

4. Remove and discard the O-rings (J090, J095).
5. Remove the coupling (J140).

J140

J095

J100

J090

J085

J120

J110

J130

J140

J095

J100

J090

J085

J120

J110

J130

P109053

Item

Wrench size

J130

9/16 inch

J110

8 mm internal hex

Repair Instructions

Series 45 Frame K2 Axial Piston Pumps

Disassembly

Danfoss | April 2017

AX00000305en-US0101 | 7

Содержание 45 K2 Series









































Результаты поиска

Содержание 45 K2 Series

Отзывы:

Похожие инструкции для 45 K2 Series

Бренды по названию

Популярные бренды

Danfoss 45 K2 Series, Инструкции по ремонту

Результаты поиска

Содержание 45 K2 Series

Отзывы:

Похожие инструкции для 45 K2 Series

Бренды по названию

Популярные бренды