S1
S2
S3
F2
F8
F3
安装爪牙螺母
Install nut screw
注意此处爪
牙螺母朝向
F3-1
Here please note
the nut direction.
Q5
S1-1
S1-2
F11-2
1
2
3
4
F4
F11x2
F1x2
F5
F9
F6
F7
3
6
F10-1
F10x2
7
5
轻木条
L15
L14
Q3
轻木条
轻木条
Q4
轻木条
S9
S10
磁铁
L6
L7
垫入第二片L7时，需稍加
打磨成斜面
圆木杆
Round wooden pole
L7
L11
注意：粘贴侧板时，有雕刻门
窗的一面朝外。
8
9
10
11
12
安装连杆导管到预留孔内,从舵机安装位
置到尾部。
安装前转向轮固定组件，用内六角螺丝固定
S6
S4
S7
S8
S5
S4-2
S4-2
S4-1
S11
S11
找出S1-S3轻木板，把他们如图粘贴在一起，待粘合
牢固后，再进行下一步骤。
机翼及尾翼请对比1:1图纸上的编号拼装，将图纸平铺到水平
工作台面上进行拼装，拼装时保持机翼平直。
拼装时注意以下细节图片
水平尾翼
Horizontal Tail
垂直尾翼
Vertical Tail
底部安装爪牙螺母
磁铁
Magnet
塑料合页
Plastic hinge
13
14
细节 Detail 1
机身组装 Fuselage Installation
机翼组装 Wing Installation
T20 Sport Scale Cessna 152
Instruction Manual
参数
翼展：1200mm
机长：870mm
起飞重量：
≈
1000-1200kg
推荐配置
推荐马达：2216-2814 900-1100KV
推荐电调：20A-40A
推荐电池：3S 2200-2800mAh
推荐舵机：9g*4pcs / 6pcs
推荐桨叶：9-11寸
通道
≥4CH
Speci�ication
Wingspan: 1200mm
Length: 870mm
Flying Weight
:≈1000-1200
g
Electric power: 2216-2814 900-1100KV
ESC: 20A-40A
Battery: 3S 2200-2800mAh
Servo
：
9g*4pcs / 6pcs
Propeller: 9-11inch
Radio≥4CH
工具 Tools Needed
此处所用轻木
条请按实际长
度自行截取。
Here please cut
the balsawood
strips according
to the actual
length by
yourself.
S4-1
Suggested Equipment
Find out S1-S3 balsawood board, stick them
together as shown.Proceed next step after glueing
them firmly.
Install nut at the bottom.
Install nut on
the back.
背面安装爪牙
螺母
Note:Put the side with laser-cut
door and window outward when
you stick the sideboard.
Balsawood strip
Balsawood strip
Balsawood strip
Balsawood strip
此处所用轻木条请按
实际长度自行截取。
Here please cut
the balsawood
strips according to
the actual length
by yourself.
Install front-wheel steering fixed parts,
fix with hexagon screw.
Install link rod duct on the
reserved hole from servo
mounting location to tail.
Build the wing and tail wing according to 1:1
drawing plan.
Put the drawing plan on horizontal workbench for
building and keep the wing straightness.
Pay attention to below details
pictures during building.
细节 Detail 2
Please polish L7 to bevel
when you assemble the
second L7.
Magnet
