background image

Motor: 2212-2216 900-1200KV

ESC: 20-30A

Propeller:  9-10 inch

Servos: 9g*4

Battery: 3s 2200-2800mAh

Radio≥4CH 

马达: 2212-2216 900-1200KV

电调: 20-30A

桨叶:  9-10寸

舵机: 9g*4

电池: 3s 2200-2800mAh

通道≥4CH 

S23 

飞行参数

推荐配置

The Piper J-3 Cub was the most popular commercial aircraft of the 1930's.  Barely seven yards long and instantly recognizable in 
its yellow-and-black paint scheme, this nostalgic favorite became the foremost trainer of the era, eventually training 80% of the 
United States' military pilots by the end of World War II.  A new Cub was rolling of the assembly line nearly every 20 minutes, and 
many of these beloved airplanes are still around today. 

Piper J-3 Cub是20世纪30年代最受欢迎的商用飞机。机身长度7码,独有的黄色和黑色涂装方案成为它标志性的特点,J-3做为那个时代最重
要的教练机型,最终在第二次世界大战结束时训练了80%的美国军事飞行员。由于简单的结构,大约每20分钟就有一个新的J-3 Cub在流水线
上生产出来,很多J-3 Cub飞机今天还在飞行。

历史背景

● 

这个产品不是玩具,而是一个复杂的具有难度的飞行器。您和您身边人的安全取决于您如何操作它,您需要了解相关知识,并谨慎操作。禁止

没有成人陪伴的儿童独自操作该设备。不适合14岁以下人群使用。再次强调,这不是一个玩具。

● 

This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends 

on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be 

accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A 

TOY.

● 

不要在机场,军事基地,居民区或其他任何受限制的地方飞行。

● 

Do not fly around some restricted location like airports, military bases, residential areas, etc.

● 

您需要对发射机进行距离检查,以确保没有收到任何干扰。

● 

You will need to range check the transmitter to be sure you are not experiencing any interference.

● 

始终保持先打开发射机后打开接收机,先关闭接收机后关闭发射机的步骤。

● 

Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.

● 

如果您是初学者,建议您在有经验玩家的协助下调试和飞行。

● 

If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from 

advanced expert fliers.

● 

请将相关物品放置在孩子们够不到的地方

● 

Keep relevant items out of reach of children.

● 

这个设备的设计已经超过我们正常使用所需要刚性要求,但若您需要以超出我们推荐的动力飞行时,请合理控制动作幅度并适当增加机体强度。

● 

This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform 

any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body 

strength.

● 

您的设备中可能包括一些玻纤和碳纤雕刻的部件,这些纤维部件所带的粉尘可能会引起眼睛,皮肤的不适,请您在需要的时候带上护目镜或者防尘服。

● 

This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the 

goggles or dust-proof clothes when needed.

● 

因航空运输安全管制,您收到的产品可能没有清单中出现过的胶水,请您理解无法发送胶水给您的原因。您可以在当地文具店很方便的购买到您所需要

的胶水。

● 

Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the 

glue you need at your local stationery store.

Balsawood Airplane

注意事项

SAFETY PRECAUTIONS

http://www.dwhobby.com/

Wingspan: 1200mm 

Length: 725mm 

Flying Weight≈750g

翼展: 1200mm 

机长: 725mm 

起飞重量≈750g

Содержание 1.2M Piper J3 Cub







Отзывы: