Danaher Motion P70360 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 56

Danaher Motion P70360 Скачать руководство пользователя страница 16

Wiring 04/06

Danaher

Motion

2.2.2.4.

General Purpose Inputs

There are nine configurable General Purpose Inputs (GPI’s) on the P70360
drive. All the inputs share a common optically isolated bus (Pull Up/Down).
The common bus simplifies the wiring allowing a common point to connect
either sinking or sourcing input devices.

Typical Input Schematic

COMMON

OPTO

INX

Configuration Examples

Sourcing input device using

P7000 internal 5 VDC supply

Sourcing input device using

external supply (+3.5 - 24 VDC)

SW1

INX

19 (+5 VDC)

20 (Pull Up/Dn)
25 Common

SW1

INX

20 (Common)

J4

J4

DC

+

-

Sinking input device using

P7000 internal 5 VDC supply

INX

19 (+5 VDC)

20 (Pull Up/Dn)
25 Common

J4

SW1

Sinking input device using

external supply (+3.5 - 24 VDC)

SW1

INX

20 (Common)

J4

DC

+

-

Internal to Drive

Internal to Drive

Internal to Drive

Internal to Drive

SW1 Input device is shown as NORMALLY OPEN. It may also be configured
via the user interface as NORMALLY CLOSED.

NOTE

For voltages greater than 5 VDC (24 VDC max), install a current
limiting resistor in series with the input.

Size according to: R

CL

= (V

S

-5)100

12 Rev

D

M-SD-7AC-01

«
...
14
15
16
17
18
...
»

Содержание P70360

























































Отзывы:

Нет отзывов