manualshive.com logo in svg

Danaher Motion P70360, Справочное руководство, Страница: 49 / 56

Поделиться
Скачать
Danaher Motion P70360 Скачать руководство пользователя страница 49

Danaher Motion 

04/06 

Appendix A 

 

When installing the P7000 into its operating location, it shall be 
ensured that any existing protective separation according to 5.2.18 of 
EN50178 is maintained throughout the entire length of the circuit in 
question. In installations the compliance for of the measures for 
protective separation shall be checked by visual inspection. 

 

Branch circuit protection consisting of a 240V, 20A circuit breaker was 
relied upon during safety testing, adequate branch circuit protection 
should be part of the final installation. 

 

Motor cable shield must be connected to protective earth.

 

 

Consult the factory before using this product on a circuit protected by a 
residual-current-operated protective device (RCD).

 

 

All covers shall be closed during operation. 

 

The P7000 drives should be used within their specified ratings. 

A.1.4 UL 

REQUIREMENTS 

The P7000 drives are UL and cUL Recognized to UL 508C under UL File 
number E137798. The following points should be considered to ensure that the 
final installation meets UL’s requirements: 

 

The drive should be used within its specified ratings. 

 

The drives shall be installed in an environment of Pollution Degree 2 or 
better. 

 

The devices shall be installed in compliance with the enclosure, and 
mounting, spacing, and segregation requirements of the ultimate 
application. 

 

Suitable grounding means shall be determined in the end product. 

 

These drives shall be used in a pollution degree 2 environment in order 
to comply with the spacing requirements of UL 840 and UL 508C. 

 

Phone jack is not for telephone connection. 

 

The terminals are suitable for factory wiring only. 

 

A UL Listed circuit breaker rated 240 V, 20 A was relied upon for 
branch circuit protection during UL testing. A suitable branch circuit 
protector should be considered when installing the device. 

 

The short circuit protective circuit and/or overload protective circuit was 
not investigated by UL. 

A.1.5 

EMC – COMPLIANCE WITH EN61800-3 

Use in a domestic environment 

 

WARNING 

The products covered in this manual are of the 
restricted sales distribution class according to IEC 
61800-3.  In a domestic environment this product 
may cause radio interference in which case the 
user may be required to take adequate measures. 

M-SD-7AC-01 Rev 

D 

45 

Содержание P70360

























































Отзывы:

Нет отзывов