Danaher Motion P70360 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 56

Danaher Motion P70360 Скачать руководство пользователя страница 44

Troubleshooting 04/06 Danaher

Motion

40 Rev

D

M-SD-7AC-01

5.3

E

XPANDED

S

TATUS

C

ODES

LED Color

Blinks

Description

Cause

Solution

Green Solid

System

OK

NA

NA

Green 1 Amplifier

is

disabled

The enable input (J4-5 & J4-6) is not
asserted if ENABLE is configured
ACTIVE CLOSED or the enable input
is asserted if ENABLE is configured
ACTIVE OPEN.

De-assert the enable input or
disable the soft shutdown
from P7000Tools.

Amber Solid

EOT±

input

latched

An EOT (End of Travel) input is
latched.

Move system in the opposite
direction until the active
EOT input transitions from
asserted to de-asserted.

Red Solid

FLASH
memory fault

A FLASH memory checksum validation
has failed indicating corruption of the
operating system.

This typically occurs during firmware
download.

Without attempting to
connect to the drive,
download the most current
firmware file from the
P7000Tools menu option
Drive->Update Operating
System…. If the FLASH
download utility fails,
contact technical support.

Red

1

Stall Fault

The Encoderless Stall Detection feature
has detected that the motor has slipped
or stalled.

Reduce move profile
acceleration, velocity,
deceleration or load inertia.
Power cycle or reset drive
via Fault Reset input or
P7000Tools.

Red 2

Over-current
Fault

An event has occurred which caused the
amplifier output current to exceed 5.6
amps.

Check motor wiring for
shorts.
Power cycle or reset drive
via Fault Reset input or
P7000Tools.

Red 3

Over-voltage
Fault

A regenerative event has occurred which
forced the bus voltage above 440 VDC.

Incoming AC line voltage too high.

Reduce deceleration, load
inertia, or reduce
deceleration duty cycle to
allow enough time for the
power dump circuit to
recover.
Power cycle or reset drive
via Fault Reset input or
P7000Tools.

Red 4

Drive

Over-

temp Fault

The temperature of the heatsink has
exceeded 70° C.

Reduce ambient temperature
or system duty cycle.
Power cycle or reset drive
via Fault Reset input or
P7000Tools.

Red

5

System Fault

An error occurred while attempting to
converge on a solution while running
the Motor Probe or Auto X-Smoothness
Probe.

Power cycle or reset drive
via Fault Reset input or
P7000Tools.

Red 6

Under-voltage
Fault

Attempting to operate the unit at a bus
voltage below 10 VDC.
Incoming AC line voltage too low.

Power cycle or reset drive
via Fault Reset input or
P7000Tools.

Red 7

EEPROM
Checksum
Fault

User non-volatile memory checksum
validation has failed indicating user
setup corruption.

Restore default
configuration from the
P7000Tools menu option
Drive->Restore Default
Configuration…

Red Constant

Blinking

Processor Fault

Illegal Address

Contact technical support.

Alternating
Red & Amber

Multi

Processor Fault

Internal system error.

Contact technical support.

«
...
42
43
44
45
46
...
»

Содержание P70360

























































Отзывы:

Нет отзывов