Danaher Motion P70360 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 56

Danaher Motion P70360 Скачать руководство пользователя страница 33

Danaher Motion

04/06

Using P7000Tools

4.4.5 COMMAND

CONFIGURATION

Command Signal Configuration

Here you can check the Step Resolution, Rotation Polarity, Enable Polarity, Stop
Rate, Rate Limit, and Velocity Limit.

Step Resolution

200 to

50,000 steps per motor revolution.

NOTE

When using a controller, set the drive resolution
equal to the controller resolution. This is particularly
important if there is position feedback to the
controller.

Step Input Filter

Check to enable low pass cutoff filter at 500 kHz to reduce
response to high frequency noise.

Rotation Polarity

Changes direction of motor rotation for a given input
command.

Enable Polarity

Active Open

Drive is enabled upon power up or external switch must

OPEN

to ENABLE drive.

Active Closed

External switch must

CLOSE

to ENABLE drive.

Stop Rate

Used by Motion Profile Generator to terminate a
programmed move.

Rate Limit

Global limit on ACCEL/DECEL in programmed moves.

M-SD-7AC-01 Rev

D

29

«
...
31
32
33
34
35
...
»

Содержание P70360

























































Отзывы:

Нет отзывов