DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 192

DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 98

98

Service Codes

TT20

Description

The Troubleshooting Tree 20 indicates an error where
the high power DC battery voltage reaches over
voltage limit and causes MCU defective state.

Note

: The DC high battery power lines

have a contactors issue. Turn Ignition off
before investigation of the contactors. For
the investigation refer to the relevant
contactor documentation.

Note

: The DC high voltage supply is

intermittent. Turn Ignition off before the
investigation of the DC battery chain from
the contactor to the MCU.

Note

: There are resonance within the DC

lines, or the regeneration torque causes
increase in voltage because of battery
resistance or the motor resolver is making
a voltage ripple.

Note

: Regarding contact intermittence to

MCU,  if  the  contactor  contacts  or  any
other  contacts  in  the  battery  chain  from
contactor  to  MCU  are  intermittent  while
the  MCU  is  in  operational  state,  it  could
make  the  DC  bus  to  fluctuate  due  to
resonances  on  the  DC  line  beyond  the
high voltage detection point.

Note

: Refer to the MCU installation guide for more

details on installation and deinstallation procedure
including safety warning considerations.

Note

: Refer to the TM4 Product installation guides for

more details on grounding (MCU and motor).

To correctly diagnose the faulty system, connect the
Diagnostic Tool (see «Diagnostics» section for test
equipment

and

descriptions)

and

follow

the

Troubleshooting Tree procedure below.

See “Safety Warnings” and “Troubleshooting Tips”
sections for general guidelines on system diagnostics.

System Mode

Referred by SysFile ID

Condition

Possible Causes

Operational

0x310B 0x310C

High power DC
voltage was higher
than the limit.

1.

Significant voltage drops meaning
numerous repeated connections and
reconnections (contactor or DC
battery chain intermittence).

2.

Affected motor resolver signal (motor
angle waveform) that creates DC
high voltage ripple.

3.

Resistive or bad grounding continuity
between the MCU and the motor
grounding points and the chassis
ground.

4.

Another external root causes.

5.

Defective MCU.

«
...
96
97
98
99
100
...
»

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды