background image

!

D

Ceramic ≥250 mm

 

Brushed steel ≥300 mm

D

Sensor

 

 WARNING

• Turn off the power to the unit before servicing or cleaning.
• Never modify the product.
• Never insert objects into any opening in the product.
• The product is not intended for playing purposes.
• Cleaning and user maintenance must be carried out by children.
• The product may only be used for the applications described in this manual.
• Do not use any accessories not recommended by the manufacturer.
• The product should be checked on a regular basis. Never use a defective or  

   malfunctioning unit

• Never make alterations to the product affecting its performance. DAN DRYER’s product 

    warranty does not cover product problems that result from misuse or alteration.

NOTE

If the power supply cord is damaged, it must be replaced immediately. Disconnect the electricity 

supply cord according to instructions.

This product is not intended for use by persons (inclusive children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised 

or have been given instruction concerning use of the product by a person responsible for their 

safety.

Children should be supervised to ensure this product is used correctly.

GENERAL SAFETY INFORMATION

INSTALLATION

• Make sure the main breaker is turned off. Installation must be carried out by a qualified 
person in accordance with applicable standards in the country concerned.

2. Mark the desired position on the wall and drill a 

 

  Ø35 mm diameter hole.

3. Installation of the tap:

 

  A) Push the screwed bushing through the hole 

 

  in the wall

 

  B) Place gasket, disc, and nut on the threaded 

 

  coupling of the tap

 

  C) Tighten with tool, be careful not to overtighten 

 

  the nut

Recommended wall 

thickness: 10-30 mm 

Gasket

Disc

Nut

Distance from 

sensor to sink:

1. Check the required distance from sensor to sink.

30°

Sensor

Sensor field of view:

 

Object distance 250 mm: D: ≤128 mm

 

Object distance 300 mm:  D: ≤155 mm

Objects within range D may cause unintentional activation.

160 mm

2. Check the required distance from sensor to sink. 

Recommended wall thickness: 10-30 mm

 19 mm

≥170 mm

30°

A minimum distance 

of 180 mm is required 

between each tap 

product. 

≥180 mm

4

5

Содержание SOAPTAP 378










Отзывы: