Dalsa LinkHS HL-HF-16K10T-00-R страница 28 Скачать руководство пользователя

Страница: 28 / 85

•

Linea HS Multifield Camera

Measuring Line (Trigger) Rate

See Camera Control Category in Appendix A for GenICam features associated with this section and

how to use them.

Related Feature: Measured Line Rate

The Measured Line Rate command is used to read the line (trigger) rate being applied, externally

or internally, to the camera.

Maximum Line Rate

The maximum achievable line rate is determined by the number of CLHS lanes and the number of

cables installed, as shown in the following table:

Camera Model

Maximum Line Rate (kHz)

(3 sensor colors output)

Maximum Line Rate (kHz)

(2 sensor colors output)

Maximum Line Rate (kHz)

(1 sensor color output)

8-bit

12-bit

8-bit

12-bit

8-bit

12-bit

HL-HF-16K10T-00-R

100 kHz

76 kHz*

150 kHz

115 kHz*

300 kHz

230 kHz*

*The Linea HS 16K 12-bit maximum line rate values shown here are theoretical. The maximum achievable line

rate depends on the frame grabber and imaging system (including CPU) used. Depending on your setup, lower

line rates may be experienced.
These line rates were achieved using an

Xtium2-CLHS PX8 (OR-A8S0-PX870)

frame grabber in a system

setup in our lab.
W

ith a system

bandwidth of 6740 MB/s the following line rates were achieved:

•

12-bit one colour: 200 kHz

For advice on your setup and achieving higher line rates, contact

Teledyne DALSA customer support

Minimum Line Rate

The minimum line rate for the camera is 300 Hz.

Scan Direction

See the section Camera Control Category in Appendix A for GenICam features associated with this

section and how to use them

Related Feature: sensorScanDirectionSource, sensorScanDirection

A TDI camera model requires the user to indicate to the camera the direction of travel of the object

being imaged.

The source of the scan direction is set using the sensorScanDirectionSource feature. The options

are: Internal, Line 2 (pin 6 on the GPIO connector), or the rotary encoder feature (using pin 5 and

pin 6 of the GPIO connector, only available when TriggerSource is “RotaryEncoder” and

rotaryEncoderOutputMode is set to “Motion”).

When set to internal, use the sensorScanDirection feature to set the direction.

Содержание LinkHS HL-HF-16K10T-00-R






















































































Результаты поиска

Содержание LinkHS HL-HF-16K10T-00-R

Отзывы:

Похожие инструкции для LinkHS HL-HF-16K10T-00-R

Бренды по названию

Популярные бренды

Dalsa LinkHS HL-HF-16K10T-00-R, Руководство пользователя

Результаты поиска

Содержание LinkHS HL-HF-16K10T-00-R

Отзывы:

Похожие инструкции для LinkHS HL-HF-16K10T-00-R

Бренды по названию

Популярные бренды