Dallas Semiconductor MAXIM DS21354 Скачать руководство пользователя

Страница: 8 / 124

DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers

8 of 124

1.2.

Document Revision History

REVISION DESCRIPTION

012799 Initial

release

012899

Corrected TSYSCLK and RSYSCLK timing and added 4.096MHz and 8.192MHz
timing

020399

Corrected definition and label of TUDR bit in the THIR register.

021199

Corrected address of IBO register in text.

040199

Added Receive Monitor Mode section

041599

Added section on Protected Interfaces

050799

Corrected pin number and description of FMS in JTAG section

072999

Added list of tables and figures

091499

Added 10

F cap to interface examples

092399

Corrected definition of

in pin description.

072401

Typo corrected in JTAG Test Access Port Pins.

021004

Added note to the Receive Information Register, FAS Resync Criteria Met.
Corrected Figures 20-1, 20-2, 20-3 with respect to

CS.

Corrected typo in Figure 18-14 (RCR1.1 reference corrected).
Corrected formatting issues.

Содержание MAXIM DS21354





























































































































Результаты поиска

Содержание MAXIM DS21354

Отзывы:

Похожие инструкции для MAXIM DS21354

Бренды по названию

Популярные бренды

Dallas Semiconductor MAXIM DS21354, Руководство пользователя

Результаты поиска

Содержание MAXIM DS21354

Отзывы:

Похожие инструкции для MAXIM DS21354

Бренды по названию

Популярные бренды