Dallas Semiconductor MAXIM DS21354 Скачать руководство пользователя | Manualshive

Страница: 7 / 124

background image

DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers

7 of 124

1.1.

Functional Description

The analog AMI/HDB3 waveform off the E1 line is transformer coupled into the RRING and RTIP pins
of the DS21354/554. The device recovers clock and data from the analog signal and passes it through the
jitter attenuation mux to the receive-side framer where the digital serial stream is analyzed to locate the
framing/multiframe pattern. The DS21354/DS21554 contain an active filter that reconstructs the analog-
received signal for the nonlinear losses that occur in transmission. The devices have a usable receive
sensitivity of 0 to -43dB, which allows the device to operate on cables over 2km in length. The receive-
side framer locates FAS frame and CRC and CAS multiframe boundaries as well as detects incoming
alarms including, carrier loss, loss of synchronization, AIS, and Remote Alarm. If needed, the receive-
side elastic store can be enabled to absorb the phase and frequency differences between the recovered E1
data stream and an asynchronous backplane clock, which is provided at the RSYSCLK input. The clock
applied at the RSYSCLK input can be either a 2.048MHz/4.096MHz/8.192MHz clock or a 1.544MHz
clock.

The transmit-side framer is totally independent from the receive side in both the clock requirements and
characteristics. Data off a backplane can be passed through a transmit-side elastic store if necessary. The
transmit formatter provides the necessary frame/multiframe data overhead for E1 transmission.

Reader’s Note:

This data sheet assumes a particular nomenclature of the E1 operating environment. In

each 125

m

s frame, there are 32 eight-bit time slots numbered 0 to 31. Time slot 0 is transmitted first and

received first. These 32 time slots are also referred to as channels with a numbering scheme of 1 to 32.
Time slot 0 is identical to channel 1, time slot 1 is identical to Channel 2, and so on. Each time slot (or
channel) is made up of eight bits, which are numbered 1 to 8. Bit number 1 is the most significant bit
(MSB) and is transmitted first. Bit number 8 is the least significant bit (LSB) and is transmitted last. The
term “locked” refers to two clock signals that are phase or frequency locked, or derived from a common
clock (i.e., a 1.544MHz clock may be locked to a 2.048MHz clock if they share the same 8kHz
component). Throughout this data sheet, the following abbreviations are used:

NAME FUNCTION

FAS Frame-Alignment

Signal

CAS Channel-Associated

Signaling

MF Multiframe

Si International

Bits

CRC4

Cyclical Redundancy Check

CCS Common-Channel

Signaling

Sa Additional

Bits

E-Bit

CRC4 Error Bits

«
...
5
6
7
8
9
...
»

Содержание MAXIM DS21354





























































































































Отзывы:

Нет отзывов

Похожие инструкции для MAXIM DS21354

Бренд: Takstar Страницы: 24

Бренд: VIETA Страницы: 66

Бренд: Harman Kardon Страницы: 24

Бренд: Harman Kardon Страницы: 2

Бренд: Harmonic Страницы: 37

Бренд: MadgeTech Страницы: 4

wM-Bus 868 USB Key

Бренд: MADD Страницы: 4

Бренд: M-system Страницы: 18

Бренд: DAPAudio Страницы: 20

Бренд: aci Страницы: 8

Бренд: aci Страницы: 4

Бренд: Triax Страницы: 36

AMG3787E-1-DR-1550-HP

Бренд: AMG Страницы: 12

Бренд: Intempco Страницы: 2

Бренд: ferroamp Страницы: 10

Бренд: Rough and Ready Страницы: 14

Бренд: Camel RF Electronic Страницы: 5

Бренд: AMG Systems Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды