manualshive.com logo in svg

DALBO MAXIROLL 1030, Руководство пользователя

Поделиться
Скачать
DALBO MAXIROLL 1030 Скачать руководство пользователя страница 6

 

 

MAXIROLL 

 

 

 

Page 6 

 

Safety 

 

This symbol appears in the instruction manual each time there is a safety warning 
concerning  your  safety,  the  safety  of  others  or  functionality  of  the  machine.  All 
safety instructions must be observed and made available to all users of the ma-
chine.  
 

General 

•

 

Ensure you are familiar with all aspects of the machine before use 

 

•

 

There are safety stickers on the machine containing important instructions for 
the safety of yourself and others, and correct use of the machine.  
 

•

 

Do not carry passengers during operation or transport. 
 

•

 

Ensure there are no personnel within the machine's working radius before op-
erating. Operate machine only from inside the tractor. 
 

•

 

When  roller  is  folded  together,  check  the  side  sections  are  locked.  Check  all 
control handles are secured against accidental operation.  
 

•

 

Before leaving the tractor or making adjustments, performing maintenance or 
repairs on the roller, extend fully and lower to ground, or maintain in transport 
position, apply tractor handbrake, switch engine off and remove ignition key to 
secure the machine against accidental operation. 
 

•

 

Remember to secure support legs and pins with split rings. 

 

•

 

Never leave driver's seat whilst machine is moving. 

 

•

 

Always adapt speed to conditions. 

 

•

 

Do not use machine unless all safety devices are in place. Defective safety de-
vices must be replaced immediately. 

Содержание MAXIROLL 1030











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды