manualshive.com logo in svg

DALBO MAXIROLL 1030, Руководство пользователя

Поделиться
Скачать
DALBO MAXIROLL 1030 Скачать руководство пользователя страница 28

 

 

MAXIROLL 

 

 

 

Page 28 

 

 

 

Activate  extend/retract  cylinders  after  fitting  until  they  show  a  little  movement. 
Reverse cylinders until they return to start position. Move cylinders backwards and 
forward several times. Raise roller fully onto wheels, extend side sections fully to 
bleed system. 
 

 

 
Ensure no personnel are within the extension radius of the side sections. 

Replacing gaskets for side section fold/unfold 
Fig. 24 

 

 

 
1.

 

For cylinder removal, see ”

Replacing extend cylinder for folding side sections

”.

 

2.

 

Drain oil from cylinder by moving ram carefully backwards and forwards. 

3.

 

Extend ram to centre position. Unscrew upper part (pos. 3) from cylinder tube 
(pos. 1). Use special tool to remove upper part. If upper part is stuck, heat front 
of sleeve. When upper part is detached from cylinder tube, pull ram up towards 
upper part and remove completely from cylinder tube. 

4.

 

Remove lock nut securing collar show (pos. 4). 

5.

 

Remove collar shoe (pos. 4) from ram. 

6.

 

Remove upper part (pos. 3) from ram. 

7.

 

Remove gaskets in upper part and collar shoe, (pos. 5+6+7+8+9). 

8.

 

Clean all parts and check for particles etc. Check for rust around scraper ring 
(pos. 5) in upper part. If detected, remove thoroughly. 

Содержание MAXIROLL 1030











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды