DALBO MAXIROLL 1030 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 42

DALBO MAXIROLL 1030 Скачать руководство пользователя страница 14

MAXIROLL

Page 14

Operation

Correct operation is vital to get the best out of your MAXIROLL 1030 or 1230. This
applies to field use and safety. Always ensure you are fully familiar with all safety
aspects of the machine.

Extending and folding up

Extending and folding the machine up must always be performed with tractor
parked.



Before extension and folding, check crackerboard is fully raised to avoid teeth col-
liding (see "Accessories, Crackerboard")

Extending

Fig. 4

1

Side sections are lifted from the
transport bar (A) using raise/lower
cylinder (marked: White).

Fig. 5

2

Activate extend/retract cylinders
(marked: Red) to fully extend side
sections.

3

Activate  raise/lower  cylinders  to
lower  roller  to  ground.  While  the
roller  is  getting  lower  is  it  very  im-
portant,  that  the  two  outer  shafts
and the middle shaft are hitting the
ground  exactly  at  the  same  time,
so  the  middle  section  won´t  get
overloaded.  Set  raise/lower  cylin-
der to flow setting last.



Before starting rolling, ensure weight transfer is correctly adjusted (see

Adjustment of hydraulic weight transfer

A

«
...
12
13
14
15
16
...
»

Содержание MAXIROLL 1030











































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды