DALBO MAXICUT Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 30

DALBO MAXICUT Скачать руководство пользователя страница 20

MAXICUT

Side 20

Adjustment

Wheels
Lubricate and adjust wheel bearings at least once annually. Check tyre pressures
(see recommended pressure on tyre).

Adjustment and lubrication of wheel bearings
1.

Remove hub caps.

2.

Remove split pin.

3.

Tighten castle nut 1/6th of a turn until hole aligns with axle. Turn wheel, check
for resistance. A little play should be detected in the hub housing when rocking
wheel from side to side. If play is excessive, repeat process.

4.

Replace split pin

5.

Fill hub cap ¾ full with grease. Replace.

Wear parts

Fig. 7

Blades  are  fitted  with  a  protective
plate at factory (A) between each one
to  protect  bolts  and  holders.  Blades
can be replaced as required. There are
2 blades per row on each roller.

Hydraulics

Check all hydraulic hoses for wear or cracks. Check all hoses for crimping.



Lubricate exposed rams with oil or pressure-resistant grease to avoid rust forming
when storing for long periods. Remember to remove before use.

A

«
...
18
19
20
21
22
...
»

Содержание MAXICUT































Отзывы:

Нет отзывов