manualshive.com logo in svg

DAL-BO MaxiDisc, Руководство пользователя

Поделиться
Скачать
DAL-BO MaxiDisc Скачать руководство пользователя страница 8

 

 

MaxiDisc 

 

 

Side 8 

 
Hydraulic System 

 

Never  allow  bystanders  within  the  operating  radius  of  the  MaxiDisc  when  the 
hydraulic  system  is  activated  to  prevent  individuals  from  the  danger  of  being 
crushed. 

 

 

Before  performing  maintenance  or  repairs  on  the  hydraulic  system,  lower  the 
implement to the ground, relieve pressure in the system, turn off the engine and 
remove the ignition key.  
 

 

Clean the hydraulic fittings thoroughly before connection. Ensure that  the pres-
sure is relieved in the hydraulic system before connecting the hydraulic hoses to 
the tractor’s hydraulic services.  

 

 

After making repairs to the hydraulic system, thoroughly bleed air out of the sys-
tem.  
 

 

Regularly  check  hydraulic  hoses  for  defects  such  as  cracks,  bends,  chafing  or 
leaks. Replace defective hoses immediately. 
 

 

Avoid spilling oil on the ground. In case of spills, collect the oil and dispose of it 
properly. 
 

 

In case skin should come in contact with hydraulic oil or grease or in case cloth-
ing should become stained with oil, remove the stained clothes immediately and 
wash the affected skin areas thoroughly. Oil and grease are harmful to the skin.  

 

 

Escaping hydraulic oil under high pressure can penetrate the skin and cause se-
vere injury. If an accident occurs, see a doctor immediately.  

 

Hitching 

 

An individual is in danger of being crushed during the hitching process. Never 
place yourself or anyone else between the tractor and the MaxiDisc, or between 
parts that must be attached or connected. 

 

Maintenance and Repairs  

 

Before servicing or making adjustments to the machine, securely block or unfold 
the machine, engage the tractor and machine brakes, turn off the engine and re-
move the ignition key.  

 

 

Tighten all nuts, bolts hydraulic fittings or any other fastened assemblies after a 
few hours’ use. Check often to make sure that they remain thoroughly tightened. 
Inspect all pins, screws and bolts for wear or damage and make sure that all are 
securely in place to avoid any possible damage or breakdown of the machine.  

 

 

Dispose of oil, grease and filters according to applicable environmental regula-
tions.  

 

Содержание MaxiDisc







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды