manualshive.com logo in svg

DAL-BO MaxiDisc, Руководство пользователя

Поделиться
Скачать
DAL-BO MaxiDisc Скачать руководство пользователя страница 21

 

 

MaxiDisc 

 

 

Side 21 

 

 

The MaxiDisc must be adjusted to operate in a perfectly level and horizontal 
position,  both  parallel  and  perpendicular  to  the  direction  of  travel,  to  obtain 
level and uniform field finishing.  

 

Hydraulic depth adjustment 

 

Fig. 12 

The  penetration  depth  can  be  freely 
adjusted  during  operation.  Adjust 
the  depth  by using the indicator (A) 
as a guide. 

 

 

 

If the packer roller sections are not working at the same depth, it is necessary 
to reset the cylinders by moving them to the fully extended position and then 
returning to the original starting depth. 

 

Angle 

The angle of the discs can be continuously adjusted hydraulically during oper-
ation,  enabling  the  operator  to  obtain  the  optimal  setting  according  to  field 
conditions.  If  there  are  many  patches  of  plant  residue  on  the  field,  the  angle 
can quickly be reduced to avoid blockage. The angle can also be reduced if the 
need for pulling force becomes too great.  
 

Travel Speed 

A  working  speed  between  8-15  km/hour  is  recommended,  but  always  drive 
according to conditions. 
 
When travel speed is increased, wear on the implement is increased, especial-
ly under dry soil conditions. Damage to the discs and T-rings may also result 
from driving too fast under unfavourable conditions.  
 

Power requirements 

Power requirements change according to soil type, terrain and travel speed. 
 
Table 2, 

Guidelines for power requirements in HP 

 

Working width  

400 cm 

500 cm 

600 cm 

Power requirements 
(hp) 

140-160 

170-190  

200-220 

 
  

A 

Содержание MaxiDisc







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды