Sportsound SSR-200 Installation & Commission Work Instructions
Page 1 of 2
DD2298507
Rev 03
01 April 2019
201 Daktronics Drive
Brookings, SD 57006-5128
www.daktronics.com/support
800.325.8766
Task (Major Step)
Process / Key Points /
Reason Why (if applicable)
Tools Required / Reference Materials
THESE ARE FIELD SERVICE INSTALLATION INSTRUCTIONS. REFER TO SUBCONTRACTOR SCOPE OF WORK FOR THEIR RESPONSIBILITIES.
1. Receive Equipment
F
Unload equipment from truck
F
Store control equipment in secure location
a.
Receive equipment.
b.
Store all front-end control equipment in a secure location
or press box
to prevent damage or theft
.
Control system
should not be left in an outdoor environment.
•
Video Playlist: SSR-200 Control System
•
SSR-200 Gen II Operation Manual
This manual includes all drawings
referenced below.
2. Inspect Equipment
F
Inspect rack equipment for damage
F
Report damage to PM
a.
Visually inspect the rack equipment for deep scratches,
dents, chips, etc.
b.
Contact PM/PC about any damaged goods.
3. Set up Control System
F
Remove front, top, and back covers
F
Set antennas at 45° angles
F
Connect Announcer’s Interface to rack
F
Connect microphone and headphones
F
Plug in power for announcer’s interface
a.
Remove front, top, and back covers from the rack.
b.
With optional wireless receiver(s) installed, position
antennas outward at 45° angles as shown in image 3b.
Optional In-Ear Monitor antenna points straight up.
Optional ADA Hearing Assist antenna is wall mounted;
mount and connect based on manufacturer’s
recommendation (within 25' of control rack).
c.
Connect interface cable between announcer’s
interface and MIC 1 and AUX 1 on side of rack.
d.
Set up wired microphone w/ stand and plug into
announcer’s interface MIC 1 INPUT jack. Plug
headphones or headset into 1/4" jack.
e.
Power announcer’s interface with provided power
supply. Use the outlets in the rack if possible.
•
Section 3
of Operation Manual
•
SSR-200 Gen II Quick Start Guide
4. Plug in and Turn on Rack
F
Connect rack to power
F
Connect rack to sound system input
F
Turn on power to the rack
F
Turn AUDIO SIGNAL switch to ON
a.
Plug control system into a power receptacle.
Power for the control rack (and fiber box) shall NOT be
on the same circuit as the All Sport console.
b.
Route the XLR cable from AUDIO OUT on the side of the
rack to a wall plate (or fiber conversion box).
c.
Switch the power strip to the ON position.
d.
Switch the AUDIO SIGNAL to ON.
•
Section 3
of Operation Manual
•
SSR-200 Gen II Quick Start Guide
5. Inspect All Source Equipment LEDs
F
Verify mixer POWER LED is on
F
Verify Announcer’s Interface POWER LED is
on
F
Verify wireless receiver(s) powered on
F
Verify CD player is on
F
Verify optional Hearing Assist System is on
F
Verify optional In-Ear Monitor System is on
a.
Verify mixer POWER LED is on.
b.
Verify Announcer’s Interface POWER LED is on.
c.
Verify one or both wireless receivers (if present) are
powered on.*
d.
Verify CD player is on.*
e.
Verify optional Hearing Assist power is on.*
f.
Verify optional In-Ear Monitor power is on.*
*LCDs display text when powered on.
6.
Test Mixer & I/O Panel
F
Connect music source into input 2
F
Set channel gain
F
Turn up channel fader
F
Turn up maser fader
F
Repeat testing for other inputs
F
Reset controls back to original settings
a.
Connect the LTIBLOX device between input 2 on the
mixer and a laptop/smartphone, and then play an
appropriate song.
b.
Verify PFL is enabled only on channel 2, use the GAIN
knob to set channel gain, and then turn off PFL.
c.
Turn up channel fader to desired level.
d.
Turn up master fader to desired level.
e.
Repeat testing for other inputs.
f.
Set controls back to original settings unless they were set
improperly.
•
Section 3
of Operation Manual
•
SSR-200 Gen II Quick Start Guide
5a. Mixer Power
3b. SSR-200 Rack
3c. Interface Cable
5b. Announcer’s
Interface Power
5c. Wireless Mic
Power
Products Involved:
SSR-200
3c & 4b. Connections
Announcer’s
Interface (Gen II)
Side View
OR
Fiber Box
(outdoor)
Wall Plate
(indoor)
