manualshive.com logo in svg

Daktronics SPORTSOUND 1500HD GEN II, Руководство по установке

Поделиться
Скачать
Daktronics SPORTSOUND 1500HD GEN II Скачать руководство пользователя страница 25

Troubleshooting

21

Replacement Parts

Sound Cabinet

Description

Part Number

1.4" Compression Driver

A-2302

8" Midrange Driver

A-2305

12" Woofer

A-2306

1500HD Mesh Replacement Kit

0A-1534-0046

     Tension Clip w/ Mandrel

HS-1613

     Tensioning Tool

TH-1175

Control Enclosure

Description

Part Number

Voltage Surge Protector

A-1129

Power Amplifier; 2800W, 4CH, Dante

A-5082165

48 VDC Power Supply

A-5099220

POE Switch

A-5110612

Fan (115 VAC)

B-1045

Padlock (order if keys are lost)

HS-1701

Thermostat

S-1247

Transformer; Audio Input, 1 Channel

T-1130

RFI Line Filter, 20 Amp

Z-1007

Fiber Conversion Box

Description

Part Number

48 VDC Power Supply

A-5099220

POE Switch

A-5110612

SFP Transceiver

A-5110614

Converter; Analog to Dante

A-5114319

Refer to 

Section 7: Daktronics Exchange and Repair & Return Programs (p�22)

 for 

information on exchanging or returning parts. 

Содержание SPORTSOUND 1500HD GEN II















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды