manualshive.com logo in svg

Daktronics CR-2004, Руководство пользователя, Страница: 51 / 90

Поделиться
Скачать
Daktronics CR-2004 Скачать руководство пользователя страница 51

 

Reference Drawings 

 

45 

Appendix A:  Reference Drawings 

Segmentation, 7 Segment Bar Digit ............................................................................ 

Drawing A-38532 

Ad Panel Mounting ....................................................................................................... 

Drawing A-52187 

Scoreboard Mounting .................................................................................................. 

Drawing A-55101 

Steel Clip Angle Mounting ............................................................................................ 

Drawing A-83301 

Address Table, 1 Through 128 .................................................................................. 

Drawing A-115078 

Address Table, 129 Through 255 .............................................................................. 

Drawing A-115079 

Schematic, Multipurpose LED DRVR ........................................................................ 

Drawing A-165028

 

4 Column MASC LED Driver Specifications .............................................................. 

Drawing A-166216 

Schematic and Digit Designation: CR-2007 .............................................................. 

Drawing

 

B-235958

 

Overall Layout; CR-2004, Multi-section ..................................................................... 

Drawing B-236615 

Schematic and Digit Designation: CR-2005 .............................................................. 

Drawing B-236704

 

Schematic and Digit Designation: CR-2008 .............................................................. 

Drawing B-236727

 

Schematic and Digit Designation: CR-2006 .............................................................. 

Drawing B-236733

 

Clip DWG; CR-2004 .................................................................................................. 

Drawing B-238471 

Schematic, Amber TNMC, GEN IV ............................................................................ 

Drawing A-252645 

Schematic, Red TNMC, GEN IV ................................................................................ 

Drawing A-252681 

Component Locations; 832/848/864 Red/Amb LED, TNMC, G4 .............................. 

Drawing A-257029 

Shop DWG, CR-2004-11/-21, Clip Mtg ..................................................................... 

Drawing B-268714

 

Specifications; LED Driver IV, 16 Col ........................................................................ 

Drawing A-288137 

Address Table 1; GEN IV Driver Address Dip Switch ................................................ 

Drawing A-290261 

Schematic; 832 / 848 / 864 Red TNMC GEN IV, 240V ............................................. 

Drawing A-294858 

Schematic; 832 / 848 / 864 Amber GEN IV, 240V ..................................................... 

Drawing A-294919 

System Riser: Computer Controlled Criket ................................................................ 

Drawing B-326325 

Component Location; CR-2004-11, -21, -12, -22 ...................................................... 

Drawing A-327249 

Address Table: Driver- MCAST G2- TNMC Switch ................................................... 

Drawing A-328274 

Schematic, OD, 3500, 34mm TNMC, Red/Amb  ....................................................... 

Drawing B-783938 

Specifications; Driver, MCAST, 4 Col ........................................................................ 

Drawing A-793970 

Schematic, OD, 3500, 34mm TNMC, Wht ................................................................ 

Drawing B-906385

 

Component Loc.; 34mm Red/Amb/Wht LED TNMC G4 ........................................... 

Drawing B-975100 

Содержание CR-2004



























































































Отзывы:

Нет отзывов