Daktronics CR-2004 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 90

Daktronics CR-2004 Скачать руководство пользователя страница 42

36

TNMC Troubleshooting & Maintenance

6.5 Component Locations & Access

Reference Drawings:

Component Locations; 832/848/864 Red/Amb LED, TNMC, G4 ............

Drawing A-257029

Component Loc.; 34mm Red/Amb/Wht LED TNMC G4 .........................

Drawing B-975100

illustrates the component locations of an 8x48-34mm display with all modules

removed. This layout will be similar for 8x32-34mm cabinets as well. The 8x64-34mm cabinets
require an additional power supply behind the sixth module. Refer to

Drawing B-975100

.

For Displays Built Before September 2009

illustrates the component locations of an older 8x48-34mm display, and this layout

will also be similar for 8x32-34mm and 8x64-34mm cabinets. Refer to

Drawing A-257029

.

Standard Daktronics outdoor LED scoreboards are typically front-accessible, but some
models may be ordered with rear service access. For that reason, Daktronics TNMCs have
been designed so that they may be accessed from both the front and rear.

Figure 23:

8x48-34 Display with Modules Removed

Figure 24:

Discontinued 8x48-34mm Display with Modules Removed

«
...
40
41
42
43
44
...
»

Содержание CR-2004



























































































Отзывы:

Нет отзывов