Daktronics BA-515 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 208

Daktronics BA-515 Скачать руководство пользователя страница 55

Scoreboard Maintenance and Troubleshooting

51

8.4 LED Drivers

Reference Drawings:

Address Table, 1 Through 128 ...............................................................

Drawing A-115078

Driver; GEN IV Outdoor LED, 16 Col Master .........................................

Drawing A-284920

Driver; GEN IV Outdoor LED, 8 Col Master ...........................................

Drawing A-284922

Specifications; LED Driver IV, 16 Col .....................................................

Drawing A-288137

Specifications; LED Driver IV, 8 Col .......................................................

Drawing A-288138

Address Table 1; GEN IV Driver Address Dip Switch ............................

Drawing A-290261

The LED drivers are located inside of a driver enclosure. The driver enclosures are found on

Drawings A-284920

and

A-284922

.

In the scoreboard, the LED drivers perform the task of switching digits on and off. To view
the LED drivers, refer to

Drawings A-284137

and

A-284138

. Each driver has up to 26

connectors providing power and signal inputs to the circuit and outputs to the digits and
indicators. The connectors function as follows:

8-Column LED Driver

Connector No.

Function

1 – 8

Output to digits and indicators

17 Controls

power/signal

16-Column LED Driver

Connector No.

Function

1 – 16

Output to digits and indicators

17 Controls

power/signal

Output connectors 1 through 16 each have nine pins. Pin 7 provides power (hot) to the digit
or indicators wired to that connector. The other eight pins provide switching connections.

For the scoreboard to receive signal and function properly, the driver must be set to the
correct address. This address is set with jumper wires in a 12-pin plug which mates with a
jack on the driver.

Drawings A-288137

and

A-288138

detail the specifications for both the 16-

and the 8-column drivers.

Address settings can be configured by using the SI dip switch. See

Drawing A-290261

for

more information. The older method using the J19 address plug is still available. Refer to

Drawing A-115078

for a listing of the wire/pin connections for driver addresses 1 – 128.

«
...
53
54
55
56
57
...
»

Содержание BA-515

















































































































































































































Отзывы:

Нет отзывов