Daktronics BA-515 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 208

Daktronics BA-515 Скачать руководство пользователя страница 53

Replacing a Digit Segment

Reference Drawing:

Digit Assemblies; LED Digits ...................................................................

Drawing B-177679

When a digit malfunctions, in most cases it is necessary to replace the entire digit circuit
board. Some larger digits (24", 30", 36", 60"), however, are constructed in segments, as shown
in

Figure 12

, and it may be possible to

make repairs by removing only the
defective segment. As with smaller digits,
the digit segment circuit boards are
mounted to the back of the digit panel.

Scoreboard Maintenance and Troubleshooting

49

Note:

Do not attempt to remove individual

LEDs.

Refer to

Drawing B-177679

.

To remove a digit segment,

follow these

steps:

1.

Open the digit panel as described
above.

2.

Disconnect the 2-pin power/signal
connector from the back of the
individual segment. Release the
connector by squeezing together
the locking tabs as you pull the
connector free.

Figure 12: Segmented Digit Panel (Rear View)

3.

The individual segments are secured to the inside of the panel with fixed machine
screws, spacers and push nuts. Remove the nuts and lift the segment off the standoff
screws.

4.

Position a new segment over the screws and tighten the nuts.

5.

Reconnect the power/signal connector.

Note:

This is a keyed connector

Β

it will attach in one way only. Do not attempt to

force the connection!

6.

Close and secure the digit panel and test the scoreboard.

Note:

Replace a malfunctioning colon, decimal or indicator assembly in the same

manner.

Replacing a Driver

Drivers are typically mounted inside the scoreboard and immediately behind a digit, but
location and mounting varies with the model of the scoreboard. Refer to the

component

locations drawings in

Section 4: Component Locations

for the location of the scoreboard

driver. All scoreboards in this manual are front-accessible. Each driver is enclosed with a
power supply and signal terminal block. Before a failed driver can be reached, the enclosure
must be accessed. Follow these steps:

«
...
51
52
53
54
55
...
»

Содержание BA-515

















































































































































































































Отзывы:

Нет отзывов