background image

7

GENERAL INFORMATION

TIRES

Check the tires frequently for cracks, checks, and proper

inflation. An under inflated tire poses a significant tipping and
braking hazard and may cause an accident, injury and death.
Do not attempt to jack or perform tire maintenance with material
in the hopper. The recommended tire pressure operating range
is 8-15 psi (55-103 kPa). Do not exceed the maximum tire
pressure listed. Tire pressure is an indication of the ground
pressure the Turf Tender has on turf; however, using a tire
pressure which is too low may cause tire problems and also
result in nonuniform ground pressure at the tire’s face.

MAINTAIN SAFE OPERATING
CONDITIONS

Check the conveyor belt for stretch and proper alignment;

adjust accordingly. The conveyor belt has a V-belt vulcanized
to the back side of the belt to help maintain proper alignment
and carry most of the load; however, it is still necessary to
check and adjust (if necessary) belt alignment.

Do not allow hydraulic fluid to come in contact with the

belt. The PVC belt material is resistant to fertilizers, but
hydraulic fluid causes the PVC coating on the belt to
decompose.

RELIEVE HYDRAULIC PRESSURE

Before performing any work on the hydraulic system, all

pressure in the system must be relieved by releasing the
engagement handle and turning the Turf Tender engine OFF.

Residual hydraulic pressure may still be present, so care

must be taken.

KEEP TURF TENDER CLEAN

Keep the Turf Tender free of excessive grass, leaves, and

accumulations of dirt and sand. Materials such as this can
compromise seals and bearings.

REPLACEMENT PARTS

To ensure optimum performance and safety, always

purchase genuine 

DAKOTA

 replacement parts and accessories.

NEVER USE “WILL-FIT” REPLACEMENT PARTS AND
ACCESSORIES MADE BY OTHER MANUFACTURERS.
Using unapproved replacement parts and accessories voids
the warranty of the 

DAKOTA

 Turf Tender.

TOWING THE TURF TENDER

Never tow the Turf Tender. Towing the Turf Tender results

in hydraulic pressure being built up and will cause damage to
the hydraulic components which will not be covered under
warranty.

GENERAL INFORMATION

Owners and operating personnel must thoroughly read and

understand this manual in order to properly operate, lubricate,
and maintain the Turf Tender. Failure to do so could result in
personal injury or equipment damage. Refer to this manual as
frequently as necessary.

LABELING AND TERMINOLOGY

The Turf Tender and this manual use the following terms

and symbols to bring attention to the presence of hazards of
various risk levels and important information concerning the
use and maintenance of the Turf Tender.

WARNING: 

Indicates presence of a hazard which can cause

severe personal injury, death, or substantial property damage
if ignored.

CAUTION:

 Indicates presence of a hazard which will or

can cause minor personal injury or property damage if ignored.

NOTE:

 Indicates supplementary information worthy of

particular attention relating to installation, operation, or
maintenance of the Turf Tender but is not related to a hazardous
condition.

Be sure to follow all instructions and related precautions as

they are meant for your safety and protection.

This manual is considered a permanent part of the Turf

Tender and must remain with the Turf Tender when sold.

Use only the correct replacement parts and fasteners. Right

and left-hand sides are determined by facing in the direction of
the steering wheel.

Record the model and serial numbers in the

specifications section so they are readily available when
contacting a dealer for parts or service.

 Many owners

employ the dealer’s Service Department for all work other
than routine care, cleaning, and adjustments. We strongly urge
the use of genuine 

DAKOTA

 parts to protect the investment

in your Turf Tender.

Our warranty is provided to support customers who operate

and maintain their equipment as described in this manual. This
warranty provides you the assurance that 

DAKOTA

 will back

its products where defects appear within the warranty period.
Should the equipment be abused, or modified to change its
performance beyond the original factory specifications, the
warranty will become void and field improvements will be
denied.

AUTHORIZED MAINTENANCE

Perform only the maintenance described in this manual that

you are qualified to perform. If major repairs are ever needed
or assistance is desired, contact an Authorized 

DAKOTA

 Dealer

for their professional service.

UNLOAD HOPPER PRIOR TO DOING
MAINTENANCE

Any material in the hopper must be removed prior to

performing maintenance on or beneath the Turf Tender.

POWER OFF MAINTENANCE AND
ADJUSTMENTS

All maintenance and adjustments to the Turf Tender must

be made with the  engine off.

Содержание 310





















Отзывы: