DAKEWE 6250 Скачать руководство пользователя страница 8

Страница: 8 / 47

Dakewe(Shenzhen)Medical Equipment Co,. Ltd

V4.1

1.2

Instrument Use

The instrument consists of 3 major parts:

• Control parts: including related function buttons and display.

• Freezer sections: quickly obtaining low temperature and slicing.

•

Refrigeration parts: including refrigeration compressor and semiconductor cooling fin.

The 6250 Semi-automatic Cryostat Microtome is used for rapid freezing of pathological

sections of human and animal body tissue. It can be widely used for preparing thin sections of

samples of varying hardness for use in pathological diagnosis, analysis and research in

hospitals, medical colleges by legal medical experts and propagation institutes.

It is used exclusively by pathology laboratories and is limited to the following tasks:

• Only operate the instrument as described in this Manual.

Any other ways of use are regarded as inappropriate!

1.3

Working principle

After the operator quickly freezes the fresh tissue hard, the frozen hard tissue is placed in a
precision-controlled slicing system, and the tissue is sliced into thin slices of the required
thickness with a blade.

1.4

Personnel Qualification

• Only trained laboratory staff can operate.

• Only operate the instrument as described in this Manual.

1.5

Instrument Model

As described in nameplate.

Product software version

Main control board:V03

，

Industrial Control Board:V02

，

Screen board:V03.

1.6

Contraindications

Not found yet.

Содержание 6250
















































Результаты поиска

Содержание 6250

Отзывы:

Похожие инструкции для 6250

Бренды по названию

Популярные бренды

DAKEWE 6250, Руководство пользователя

Результаты поиска

Содержание 6250

Отзывы:

Похожие инструкции для 6250

Бренды по названию

Популярные бренды