background image

 DTP10-L hardware user

’s manual 

 

DAINCUBE   Corp.                                                                         

 

33 / 42 

 

8.3.6.  Method wiring 

 

(1)  Signal and communication cables is placing a high-voltage cable or power line over a 

distance of 10cm, please not affected by the noise and magnetic field 

(2)  If possible use separate ducts for power cables and control lines. 
(3)  All cable should be the Shield cable. 

 

 

(4)  Minimizing the loops 

 

[Figure 8-13] Avoiding loops in wiring designs 

 

 

Note

:  

Wires that form a loop make an efficient antenna. Run feed and return wires together rather than 
allowing a loop to form. Twisting the pair further reduces the antennae effects and can 
significantly reduce EMI.

 

 

(5)  Excess cable

 

 
 

 

Better solution                              Good solution                  Not recommended 

[Figure 8-14] Excess cable treatment 

 

(6) 

Cabling instructions

 Do not coil excess cable of different types (for example, motor power and feedback) together. An efficient 

transformer is formed at HF. 

 Cable lengths should ideally be trimmed to fit the application. 

 If excess cable cannot be trimmed, it should be laid in an 'S' or figure eight pattern (refer to the figure 

below). 

 

  

Note

 

According to the NFPA79 approved by the United States, when the shielded wire is not 
used for wiring between a servo amplifier and a servo motor, the wiring must be 
insulated from wiring of other control or signal circuits. 
(Example: 100 mm or more for 20 A or less) 

Содержание DTP10-L











































Отзывы: