manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 161

Symptom List:

P0700-TRANS CONTROL 1-2/4-5 SOLENOID CIRCUIT
P0700-TRANS CONTROL 2-3 SOLENOID CIRCUIT
P0700-TRANS CONTROL 3-4 SOLENOID CIRCUIT
P0700-TRANS CONTROL INTERNAL CONTROLLER
P0700-TRANS CONTROL MOD. PRESS SOLENOID CIRCUIT
P0700-TRANS CONTROL SHIFT PRESSURE SOLENOID CIRCUIT
P0700-TRANS CONTROL SOLENOID SUPPLY VOLTAGE
P0700-TRANS CONTROL TCC SOLENOID CIRCUIT
P0702-TRANS CONTROL ABS SENSOR MESSAGE
P0702-TRANS CONTROL ENGINE T-CASE SWITCH MESSAGE
P0702-TRANS CONTROL IMPROPER GEAR
P0702-TRANS CONTROL IMPROPER RATIO OR TRANSMISSION
SLIPPING
P0702-TRANS CONTROL INTERNAL SHIFTER FAILURE
P0702-TRANS CONTROL N2 OR N3 INPUT SENSOR CIRCUIT
P0702-TRANS CONTROL TCC FAULT

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0700-TRANS CONTROL 1-2/4-5
SOLENOID CIRCUIT.

POSSIBLE CAUSES

VERIFY CURRENT DTC

TEST

ACTION

APPLICABILITY

1

NOTE: If DTC P1242 is present with this DTC, perform the diagnostic for
P1242 before continuing.
NOTE: This code was set in the ECM by the Transmission Control Module to
indicate a transmission fault. Diagnosis of transmission faults should be
done using the Transmission Diagnostic Information.
NOTE: When repairs have been completed, the ECM and TCM must have
codes cleared.
Turn the ignition on.
With the DRBIII

t

, erase ECM DTCs only.

With the DRBIII

t

, read ECM DTCs.

Are any P0700 or P0702 DTCs present in the ECM?

All

Yes

→

Refer to Transmission Diagnostic Information for the related
symptom(s).
Perform W5J400 TRANSMISSION VERIFICATION TEST - VER
1.

No

→

Test Complete.

153

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды