Daikin VRV RXYMQ-A Series Скачать руководство пользователя страница 278

Страница: 278 / 305

Check

SiME332106E

272

Part 6 Service Diagnosis

Note(s)

Reference

6.2 Low Pressure Check

CHECK 2

Referring to the Fault Tree Analysis (FTA) shown below, probe the defective points

CHECK 7

Refer to page 279.

CHECK 8

Refer to page 280.

Abnormal drop in

low pressure

(Low evaporating

temperature)

[In cooling]

(

Defective
low pressure
control

Defective
compressor
capacity
control

Defective low pressure

sensor

Defective main PCB

Defective
low pressure
protection
control

Defective low pressure
sensor

Defective hot gas EV

Defective main PCB

[In both cooling
and heating]
(

[In cooling]
If the indoor unit
electronic
expansion valve is
throttled too much:
(

Defective indoor
unit electronic
expansion valve

Defective valve coil

Defective valve body

Defective
control

Defective gas pipe
thermistor of indoor unit

Defective liquid pipe
thermistor of indoor unit

Defective main PCB

Defective outdoor
unit electronic
expansion valve

Defective valve coil

Defective valve body

[In heating]
If the outdoor unit
electronic
expansion valve
excessively
throttled:
(

Defective
control

Defective low pressure

sensor
Defective suction pipe

thermistor

Defective main PCB

[In cooling]

Low suction air
temperature of
the evaporator

[In heating]

Low suction air
temperature of
indoor unit

Short circuit

Low room temperature

Defective suction air thermistor of indoor unit

Low suction air temperature of outdoor unit

Defective outdoor air temperature thermistor of outdoor unit

High pipe
resistance

Abnormal piping length

Bent or crashed pipe

Clogging of foreign materials

Stop valve closed

Less
circulation
quantity of
refrigerant

Degradation
in evaporating
capacity

Refrigerant shortage

Moisture choke

Dirty evaporator

Decreased
airflow rate

Decreased
fan output

Defective fan motor

Is there any obstacle in the airflow passage?

Defective main PCB
(Including capacity setting)

High
airflow
passage
resistance

Dirty filter

Obstacle

Defective electronic
expansion valve
control

Are the coil resistance and insulation normal?

Check for the thermistor resistance and connection.

Are the voltage characteristics normal?

Are the coil resistance and insulation normal?

Is the pressure value checked with the Service Checker corresponding
to the measurement value of the pressure sensor?

Check for the thermistor resistance and connection.

Is the suction air temperature less than 14°C?

Is the room temperature less than 14°C?

Eliminate moisture by vacuum operation. (Refer to

CHECK 8.

)

Is the pressure value checked with the Service Checker

corresponding to the measurement value of the pressure sensor?

Are the voltage characteristics normal?

Is the pressure value checked with the Service Checker corresponding

to the measurement value of the pressure sensor?

Are the voltage characteristics normal?

Can the fan motor be rotated with hands?

Are the motor coil resistance and insulation normal?

Is the air filter clogged?

If a spare PCB is mounted, is the

capacity setting properly made?

Is the heat exchanger clogged?

Refer to

CHECK 7.

Does the piping length fall in the permissible range?

Conduct visual checks for pipe conditions.

Is there any temperature difference caused before and after the filter or

branch pipe?

Check to be sure the stop valve is open.

Is the connector properly connected?

Are the thermistor resistance characteristics normal?

Is the outdoor air temperature less than –20°C?

Is the connector properly connected?

Are the thermistor resistance characteristics normal?

Defective valve coil

Defective valve body

Are the coil resistance and insulation normal?



1. For details of compressor capacity control while in cooling refer to Compressor

Capacity Control on page 56.



2. The “low pressure protection control” includes low pressure protection control and

hot gas bypass control.



3. In cooling, the indoor unit electronic expansion valve is used for “superheating

degree control”.



4. In heating, the outdoor unit electronic expansion valve is used for “superheating

degree control of outdoor heat exchanger”.

Содержание VRV RXYMQ-A Series


















































































































































































































































































































Результаты поиска

Содержание VRV RXYMQ-A Series

Отзывы:

Похожие инструкции для VRV RXYMQ-A Series

Бренды по названию

Популярные бренды

Daikin VRV RXYMQ-A Series, Руководство по обслуживанию

Результаты поиска

Содержание VRV RXYMQ-A Series

Отзывы:

Похожие инструкции для VRV RXYMQ-A Series

Бренды по названию

Популярные бренды