Daikin VRV RXYMQ-A Series Скачать руководство пользователя страница 228

Страница: 228 / 305

Troubleshooting by Error Code

SiME332106E

222

Part 6 Service Diagnosis

5.41 Inverter Radiation Fin Temperature Rise Abnormality

Applicable
Models

All outdoor unit models

Error Code

Method of Error
Detection

Detect temperature of power module of the inverter circuit.

Error Decision
Conditions

Thermistor located inside the power module of the inverter circuit for compressor and fan motor.
Cooling tube plate poor heat-exchange.

Supposed
Causes



Radiation fin temperature rise of fan circuit



Cooling tube plate not fixed with screws



error



Defective inverter circuit



High outdoor air temperature



Closed stop valve

Troubleshooting



Subcode L4-01

Defective radiation from the power
unit
• Blocked air suction port
• Stained radiation fin
• High outdoor air temperature

Connect the connector correctly.

Eliminate

error.

Keep operating.

Replace the relevant PCB

(

1).

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

Caution

YES

Is the radiation fin

temperature greater than the

designed temperature?

Does the remote

controller display error

code

Does the

connector X111A of fin

thermistor connect to the

outdoor unit main PCB

correctly?

When the unit starts

operating, is the error code

displayed again?

Connect to the power and then press
the

INSPECTION/TEST

button on

remote controller.

Open the stop valve.

YES

Is the stop valve open?

Содержание VRV RXYMQ-A Series


















































































































































































































































































































Результаты поиска

Содержание VRV RXYMQ-A Series

Отзывы:

Похожие инструкции для VRV RXYMQ-A Series

Бренды по названию

Популярные бренды

Daikin VRV RXYMQ-A Series, Руководство по обслуживанию

Результаты поиска

Содержание VRV RXYMQ-A Series

Отзывы:

Похожие инструкции для VRV RXYMQ-A Series

Бренды по названию

Популярные бренды