Daikin Trailblazer AGZ030E-070E Скачать руководство пользователя

Страница: 95 / 148

Circuit Functions

www.DaikinApplied.com 95

IOM 1207-6 • TRAILBLAZER

MODEL AGZ CHILLERS

Cycle Timers

A minimum time between starts of the compressor and a

minimum time between shutdown and start of the compressor

shall be enforced. The time values are determined by the

Start-start Timer and Stop-start Timer setpoints.
These cycle timers should not be enforced through cycling of

power to the chiller. This means that if power is cycled, the

cycle timers should not be active.
These timers may be cleared via a setting on the controller.

Condenser Fan Control

Condenser fan control should stage fans as needed any time

compressors are running on the circuit. All fans and solenoid

valves will be off when the circuit is in the off and preopen

states. Condenser fan digital outputs will be turned on or

off immediately for condenser stage changes. Condenser

solenoid valve outputs will turn on immediately when a stage

up requires the output to turn on, but will have a delay for

turning off during a stage down. This delay is 20 seconds. If

the circuit shuts off then the condenser solenoid valve outputs

will turn off without a delay.

Condenser Staging

Condenser staging will use up to 5 digital outputs for control of

condenser fans and a digital output for control of a condenser

solenoid valve. When equipped with condenser fan VFDs, the

speed signal(s) also starts and stops the fan that is connected

to the VFD. The total number of fans on shall be adjusted

with changes of one fan at a time. The tables below show the

outputs energized for each stage.

Figure 72: 2 Fans per Circuit - Unit Numbering Schematic

Table 57: 2 Fans per Circuit - Without Fan VFD

Circuit 1

Description

Output

Fans

Stage

Fan Output 1

UC DO3

Fan 11 On On --

Fan Output 2

UC DO4

Fan 12

On --

Circuit 2

Description

Output

Fans

Stage

Fan Output 1

UC DO7

Fan 21 On On --

Fan Output 2

UC DO8

Fan 22

On --

Table 58: 2 Fans per Circuit - With 1 Fan VFD per Circuit

Circuit 1

Description

Output

Fans

Stage

Speed Signal 1 UC X5

Fan 11 On On --

Fan Output 2

UC DO4

Fan 12

On --

Circuit 2

Description

Output

Fans

Stage

Speed Signal 1 UC X6

Fan 21 On On --

Fan Output 2

UC DO8

Fan 22

On --

Figure 73: 3 Fans per Circuit - Unit Numbering Schematic

Table 59: 3 Fans per Circuit - Without Fan VFD

Circuit 1

Description

Output

Fans

Stage

Fan Output 1

UC DO3

Fan 11

On On On --

Fan Output 2

UC DO4

Fan 12

On On --

Fan Output 3

UC DO5

Fan 13

Condenser SV UC X7

SV 11

Circuit 2

Description

Output

Fans

Stage

Fan Output 1

UC DO7

Fan 21

On On On --

Fan Output 2

UC DO8

Fan 22

On On --

Fan Output 3

UC DO9

Fan 23

On --

Condenser SV UC X8

SV 21

On --

Control Panel

Fan 11

Fan 21

Fan 22

Fan 12

2-Fan Unit Locations and Numbering

Control Panel

Fan 11

Fan 12

Fan 21

Fan 23

Fan 13

Fan 22

3-Fan Unit Locations and Numbering

Содержание Trailblazer AGZ030E-070E





















































































































































Результаты поиска

Содержание Trailblazer AGZ030E-070E

Отзывы:

Похожие инструкции для Trailblazer AGZ030E-070E

Бренды по названию

Популярные бренды

Daikin Trailblazer AGZ030E-070E, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Trailblazer AGZ030E-070E

Отзывы:

Похожие инструкции для Trailblazer AGZ030E-070E

Бренды по названию

Популярные бренды