Daikin Super Multi NX FLKS25BAVMB Скачать руководство пользователя страница 59

Страница: 59 / 144

SiBE05-722EE

Control Specification

Functions and Control

3.8

Outdoor Fan Control

1. Fan ON control to cool down the electrical box

The outdoor fan is turned ON when the electrical box temperature is high while the compressor
is OFF.

2. Fan OFF control during defrosting

The outdoor fan is turned OFF during defrosting.

3. Fan OFF delay when stopped

The outdoor fan is turned OFF 60 seconds after the compressor stops.

4. Fan speed control for pressure difference upkeep

The rotation speed of the outdoor fan is controlled for keeping the pressure difference during
cooling operation with low outdoor temperature.

When the pressure difference is low, the rotation speed of the outdoor fan is reduced.

When the pressure difference is high, the rotation speed of the outdoor fan is controlled as
well as normal operation.

5. Fan speed control during forced cooling operation

The outdoor fan is controlled as well as normal operation during forced cooling operation.

6. Fan speed control during POWERFUL operation

The rotation speed of the outdoor fan is increased during POWERFUL operation.

7. Fan speed control during indoor / outdoor unit quiet operation

The rotation speed of the outdoor fan is reduced by the command of the indoor / outdoor unit
quiet operation.

8. Fan ON/OFF control when operation (cooling, heating, dry) starts / stops

The outdoor fan is turned ON when the operation starts. The outdoor fan is turned OFF when
the operation stops.

3.9

Liquid Compression Protection Function

Outline

In order to increase the dependability of the compressor, the compressor is stopped according
to the outdoor temperature.

Detail

Operation stops depending on the outdoor temperature.
Compressor turns off under the conditions that the system is in cooling operation and outdoor
temperature is below –12°C.

Содержание Super Multi NX FLKS25BAVMB

















































































































































Результаты поиска

Содержание Super Multi NX FLKS25BAVMB

Отзывы:

Daikin Super Multi NX FLKS25BAVMB, Руководство по обслуживанию, Страница: 59 / 144

Результаты поиска

Содержание Super Multi NX FLKS25BAVMB

Отзывы: