manualshive.com logo in svg

Daikin RoCon HP, Руководство по эксплуатации

Поделиться
Скачать
Daikin RoCon HP Скачать руководство пользователя страница 40

Operating instructions

40

 Daikin RoCon HP 

Daikin Control

008.1420844 – 05/2014

5 

x

 Parameter settings

5.10 Rotary switch setting: Info 

Parameter

Description

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

Overview

Display of different current operating data (see chapter 3.4.1).

S

S

-

-

-

Water Pressure

The current water pressure is displayed in bar.

S

S

0 - 4 bar

-

0.1 bar

T-HS

The current temperature (TVBH) of the heat generator is displayed in °C.

S

S

0 - 100 °C

-

1 °C

T-HS Setpoint

The current Inflow target temperature of the heat generator is displayed in °C 
(see chapter 3.6.4).

S

S

0 - 90 °C

-

0.1 °C

T-Outside

The current external temperature is displayed °C.

S

S

-39 to +50 °C

0.1 °C

T-DHW

The current temperature of the hot water storage tank is displayed in °C. If there is no hot water 
function activated, "- - -" is displayed.

S

S

0 - 100 °C

-

0.1 °C

T-DHW Setpoint

The current target hot water temperature is displayed °C. If there is no hot water function acti-
vated, "- - -" is displayed. The current set value is here always the maximum value of all rele-
vant demands for this hot water circuit.

S

S

10 - 70 °C

-

0.1 °C

T-Return

The current return flow temperature of the heat generator is displayed in °C. If there is no rel-
evant sensor connected to the heat generator, "- - -" is displayed.

S

S

0 - 100 °C

-

0.1 °C

Flow Rate

The filtered value of the current volume flow in litres per hour is displayed.

S

S

0 - 5100 l/h

-

l/h

T-HC

The inflow temperature in the direct heating circuit is displayed in °C.

S

S

0 - 100 °C

-

0.1 °C

T-HC Setpoint

The set temperature of the flow in the direct heating circuit is displayed in °C.

S

S

0 - 90 °C

-

0.1 °C

Status HS pump

The current status of the internal heat circulation pump in the Daikin Altherma EHS(X/H) is dis-
played.

S

S

Off
On

-

-

Runtime Compres-
sor

The running time of the refrigerant compressor is displayed in h.

S

S

-

-

h

Runtime Pump

The running time of the internal heating circulation pump is displayed in h.

S

S

-

-

h

Mixer Position

The current position of the 3UV DHW 3-way switch valve is displayed.
0 %: Position A (room heating)
100 %: Position B (domestic hot water generation)

S

S

0 - 100 %

-

1 %

Qboh

The amount of heat in the additional heat generator for hot water generation is displayed in 
kWh.

S

S

-

-

kWh

Qchhp

The amount of heat in the additional heat generator for heating mode is displayed in kWh.

S

S

-

-

kWh

Qsc

The quantity of heat in the heat pump for cooling is displayed in kWh.

S

S

-

-

kWh

Qch

The quantity of heat in the heat pump for heating is displayed in kWh.

S

S

-

-

kWh

QWP

The total amount of heat in the heat pump is displayed in kWh.

S

S

-

-

kWh

Qdhw

The quantity of heat for hot water generation is displayed in kWh.

S

S

-

-

kWh

HS type

The heat generator type Daikin Altherma EHS(X/H) detected is displayed.

S

S

-

-

-

Sw Nr B1/U1

The software and version of the RoCon B1 operating unit is displayed.

S

S

-

-

-

Sw Nr Controller

The software number and the version of the RoCon BM1 circuit board are displayed.

S

S

-

-

-

Sw Nr RTX RT

The software number and the version of the RTX-AL4 circuit board are displayed.

S

S

-

-

-

Tab. 5-12 Parameter in rotary switch setting "Info"

Содержание RoCon HP





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды