Daikin RoCon+ HP Series, Руководство по эксплуатации

Страница: 36 / 516

7 Parameter settings
Operating Instructions
36
Daikin RoCon+ HP
Daikin controller RoCon+ HP1
008.1447899_00 – 09/2019 – EN
Parameters Setting range
Min / Max
Description Factory
setting
Incre-
ment
Access
BE HF
AUX switching
function Setting assigns the switching conditions for the potential-free AUX switch-
ing contact (toggle switch output A, see
Chap. 4.4.4 ).
- N E
Inactive Function deactivated.
AUX switching contact switches:
Switching
threshold TDHW
(AUX)
If storage tank temperature (Tdhw) ≥ value of [Switching threshold TDHW
(AUX)] parameter.
Heating/cooling
request
If a cooling request or heating request is present.
BUH request If a hot water request to the backup heater (EKBUxx) is present or the con-
figured backup heater is requested for heating support.
Error If an error is pending
TVBH > 60 °C If the sensor value (TVBH) is > 60 °C.
Outside temper-
ature
If the outside temperature is < [Bivalence temperature] parameter value.
(heat pump continues to operate = parallel equilibrium mode)
Outside temp. +
DHW/heating
If the outside temperature is < [Bivalence temperature] parameter value +
a heating request or a hot water request is present. (heat pump does not
continue to operate = alternative equilibrium mode)
DHW request If a hot water request is present.
Outside temper-
ature + heating
If the outside temperature is < [Bivalence temperature] parameter value +
"room heating" heat request (not for hot water request). Heat pump no
longer operates in room heating mode below the value set in the [Bi-
valence temperature] parameter – only in hot water mode.
Application: Alternative room heating bi-valence mode if the boiler is hy-
draulically integrated so that it directly heats the unpressurised storage
tank water of the Daikin Altherma ETS(X/H) (connection via solar connec-
tions).
Multi-oil If the outside temperature is < [Bivalence temperature] parameter value +
"room heating" heat request (not for hot water request). Heat pump no
longer operates in room heating mode below the value set in the [Bi-
valence temperature] parameter – only in hot water mode.
Application: Alternative room heating equilibrium mode if the boiler is hy-
draulically integrated in the heat pump feed. For this application type, the
frost protection function must be deactivated on the Daikin Altherma
ETS(X/H) ([Frost protection temperature] parameter = Off).
Cooling mode If the heat pump is in the "Cooling" operating mode.
AUX wait time 0 – 600 s AUX switching contact (A) only switches after a delay if the switching con-
dition (see [AUX switching function] parameter) is present for longer than
the set time. 120 s 5 s N E
Switching
threshold
TDHW (AUX) 20 – 85 °C Storage tank temperature (Tdhw) switching threshold for AUX switching
contact (see [AUX switching function] parameter). 50 °C 1 °C N E
Tab. 7-11 Parameter in the "Inputs/Outputs" menu
7.5.5 Menu: Intelligent Storage Mgmt
[→ Main menu → Settings → ISM]
Parameters Setting range
Min / Max
Description Factory
setting
Incre-
ment
Access
BE HF
Continuous
heating This function enables uninterrupted heating, even when the evaporator is
being defrosted. This enables high comfort to be guaranteed, even with
rapidly reacting heating systems (e.g. convectors). - N E
Off No uninterrupted heating
On Uninterrupted heating. When the evaporator is being defrosted, heat for
heating is taken from the storage tank.
Heating sup-
port (HZU) Heating support from hot water storage tank if minimum temperature is ex-
ceeded (see
Chap. 4.4 and [Heating support hysteresis] parameter).
- N E
Off No heating support
On Heating support function active