Daikin RoCon BF Скачать руководство пользователя страница 54

Страница: 54 / 64

Operating instructions

Daikin RoCon

Daikin Control unit

008.1543999_00 – 03/2017 – EN

Errors and faults

7.2

Emergency operation

For faults or incorrect settings of the electronic control unit,
emergency heating operation (manual operation) can be
maintained.
Please observe the supplementary notes for this in the instal-
lation manual of the heat generator.

1. Push the Exit button for at least 5 s.



The

"Special Level"

menu is displayed.

2. Use the rotary button to select the

"Manual Operation"

level.



Temperature scale, target and target T-HS are displayed.

3. Use the rotary button to set the target T-HS.



The Daikin heat generator works manually at the target T-
HS.

4. Cancellation and jump back by pushing the Exit button again.

Fig. 7-4

Software information of the control unit components

Info

Overview

Water Pressure

T-HS

Sw Nr B1/U1

Sw Nr FA

Info

Sw Nr B1/U1

Sw Nr Controller

Sw Nr FA

Info

Sw Nr B1/U1

Sw Nr mixing valve

Sw Nr Controller

Содержание RoCon BF
































































Результаты поиска

Содержание RoCon BF

Отзывы:

Daikin RoCon BF, Руководство по эксплуатации, Страница: 54 / 64

Результаты поиска

Содержание RoCon BF

Отзывы: