Daikin RMXS-L Series Скачать руководство пользователя страница 178

Страница: 178 / 250

Troubleshooting for FFQ Series

SiUS181305E

169

Troubleshooting

5.3

Fan Motor or Related Abnormality

Error Code

Method of Error
Detection

The signal from the fan motor detects abnormal fan speed.

Error Decision
Conditions

The fan rotations are not detected while the output voltage to the fan is at its maximum.

Supposed
Causes



Disconnection, short circuit or disengagement of connector in fan motor harness



Defective fan motor (disconnection, poor insulation)



Abnormal signal from fan motor (faulty circuit)



Defective indoor unit PCB



Momentary fluctuation of power supply voltage



Fan motor lock
(Caused by motor or other external factors)



Fan does not rotate due to tangled foreign matters.

Troubleshooting

Note:

1. Check the connector of fan motor. (Power supply cable)
2. Turn OFF the power supply.
3. Measure the resistance between the terminals at the motor side connectors to check that there

is no short circuit, while the connector is disconnected.

FFQ series

YES

Is the

harness from the

fan motor correctly

connected to the

indoor unit

PCB?

YES

Is there any

foreign matter around

the fan?

Is there

short circuit between

the terminals?

YES

Turn off the power supply.

Check the fan motor
connector. (See the Note.)

Remove the foreign matter.

Connect the connector
correctly.
X20A: FFQ series

Replace the fan motor.

Replace the indoor unit PCB.

(R18389)

Caution

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

Measuring points

Resistance for judgement

(1) - (3)

88.2



± 10%

(2) - (3)

85.5



± 10%

(1) Red

(2) White

(3) Black

(R18060)

Содержание RMXS-L Series



























































































































































































































































Результаты поиска

Содержание RMXS-L Series

Отзывы:

Похожие инструкции для RMXS-L Series

Бренды по названию

Популярные бренды

Daikin RMXS-L Series, Руководство по обслуживанию

Результаты поиска

Содержание RMXS-L Series

Отзывы:

Похожие инструкции для RMXS-L Series

Бренды по названию

Популярные бренды