Daikin REYQ96MTJU, Инструкция по проектированию, установке и испытаниям, Страница: 90 / 236

Test Operation Si39-406
84 General Information
Setting item 0 Display contents of “Number of units for sequential start, and
others”
No. Setting item
LED display
Data display
H1P H2P H3P H4P H5P H6P H7P
0
Number of units for sequential
starting, and others
9 7 7 7 7 7 7
See below
1 —
Lower 6 digits
2 Low noise/demand address
9 7 7 7 7 8 7
3 Not used
9 7 7 7 7 8 8
4 Airnet address
9 7 7 7 8 7 7
5 Number of connected indoor units
9 7 7 7 8 7 8
6 Number of connected BS units
9 7 7 7 8 8 7
7
Number of connected zone units
(excluding outdoor and BS unit)
9 7 7 7 8 8 8
8 Number of outdoor units
9 7 7 8 7 7 7
9 Number of connected BS units
9 7 7 8 7 7 8
Lower 4 digits:
upper
10 Number of connected BS units
9 7 7 8 7 8 7
Lower 4 digits:
lower
11
Number of zone units (excluding
outdoor and BS unit)
9 7 7 8 7 8 8
Lower 6 digits
12 Number of terminal blocks
9 7 7 8 8 7 7
Lower 4 digits:
upper
13 Number of terminal blocks
9 7 7 8 8 7 8
Lower 4 digits:
lower
14 Contents of malfunction (the latest)
8 7 7 8 8 8 7
Malfunction
code table
15
Contents of malfunction
(1 cycle before)
8 7 7 8 8 8 8
16
Contents of malfunction
(2 cycle before)
8 7 8 7 7 7 7
20 Contents of retry (the latest)
8 7 8 7 8 7 7
21 Contents of retry (1 cycle before)
8 7 8 7 8 7 8
22 Contents of retry (2 cycle before)
8 7 8 7 8 8 7
Number of units for sequential
start 1 unit
9 7 7 7 7 7 7
2 units
9 7 9 7 7 7 7
3 units
9 7 8 7 7 7 7
EMG operation /backup operation
setting ON
9 7 7 8 7 7 7
OFF
9 7 7 7 7 7 7
Defrost select setting Short
9 7 7 7 8 7 7
Medium
9 7 7 7 9 7 7
Long
9 7 7 7 7 7 7
Te setting H
9 7 7 7 7 8 7
M
9 7 7 7 7 9 7
L
9 7 7 7 7 7 7
Tc setting H
9 7 7 7 7 7 8
M
9 7 7 7 7 7 9
L
9 7 7 7 7 7 7
c. Monitor mode
<Selection of setting item>
<Confirmation on setting contents>
To enter the monitor mode, push the
MODE button (BS1) when in
“Setting mode 1”.
Push the SET button (BS2) and set
the LED display to a setting item.
Push the RETURN button (BS3) to
display different data of set items.
Push the RETURN button (BS3) and
switches to the initial status of
“Monitor mode”.
∗
Push the MODE button (BS1) and
returns to “Setting mode 1”.
(V2765)