Daikin Modular L Smart Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 90

background image

ESIE19-06

|

Part 2. Troubleshooting

2.2. Error based troubleshooting

Page 28

21/01/20

|

Version 1.1

Modular L Smart

2.2.2. System

2.2.2.1. “U5-00” – Transmission user interface PCB abnormality

2.2.2.2. “U8-00” – Main-Sub control error

Trigger

Effect

Reset

Main PCB A1P detects abnormal/missing
transmission to user interface for a certain
time.

Unit will stop operating.

Automatic reset.

Possible cause

Check

Corrective action

Faulty main PCB.

Check if the main PCB receives power.
Check if the HAP LED is blinking in regu-
lar intervals.
Check if the correct spare part is installed.
Check the wiring to main PCB.
Check voltage P1P2 ±16 VDC.

Adjust power to the main PCB.
Replace main PCB when HAP LED is not
blinking in regular intervals.
Install correct spare part or update main
PCB.
Adjust wiring to main PCB when required.

Faulty user interface.

Check user interface.

Replace user interface when required.

User interface is not detected anymore
since power was connected.

Check the wiring between main PCB and
user interface.

When user interface is required, (re-) con-
nect user interface to main PCB terminals
P1P2.
When user interface is not further
required, reset power of HRV unit.

External factor (e.g. electrical noise) (error
disappears after power reset, but returns
after a while).

Check for source which could cause elec-
trical interference.

Avoid electrical interference.

Trigger

Effect

Reset

Main PCB A1P detects abnormal/missing
transmission to dual interfaces.

Unit will stop operating.

Power reset.

Possible cause

Check

Corrective action

Combination of 1 or 2 user interfaces
does not correspond to the Main-Sub set-
ting on the interfaces.

Check the setting of the Main and Sub
control setting.
Check wiring P1P2 between main PCB
and interface(s).
Check voltage P1P2 ±16 VDC.

When only 1 interface is connected,
ensure set to "Main".
When 2 user interfaces are connected,
ensure 1st user interface set to "Main",
2nd user interface set to "Sub".

Faulty user interface.

Check user interface.

Replace user interface when required.

Faulty main PCB.

Check if the main PCB receives power.
Check if the HAP LED is blinking in regu-
lar intervals.
Check if the correct spare part is installed.
Check the wiring to main PCB.
Check voltage P1P2 ±16 VDC.

Adjust power to the main PCB.
Replace main PCB when HAP LED is not
blinking in regular intervals.
Install correct spare part or update main
PCB.
Adjust wiring to main PCB when required.

Faulty user interface.

Check user interface.

Replace user interface when required.

External factor (e.g. electrical noise) (error
disappears after power reset, but returns
after a while).

Check for source which could cause elec-
trical interference.

Avoid electrical interference.

«
...
26
27
28
29
30
...
»

Содержание Modular L Smart



























































































Отзывы:

Нет отзывов

Похожие инструкции для Modular L Smart

Helios KWL-SPV 1900

Бренд: Salda Страницы: 34

Бренд: Mandelli Страницы: 4

Vision CAC 003 C

Бренд: Daikin Страницы: 86

Бренд: Haier Страницы: 36

Бренд: Troges Страницы: 48

Бренд: Lennox Страницы: 12

VOLCANO VR Mini

Бренд: VTS Medical Systems Страницы: 21

Бренд: VTS Medical Systems Страницы: 24

Бренд: VTS Medical Systems Страницы: 32

Бренд: Frico Страницы: 12

Бренд: Frico Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды