Daikin McQuay AGZ-D Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 82

Daikin McQuay AGZ-D Скачать руководство пользователя страница 16

16

AGZ 025D through 190D

OMM 1087

Digital Outputs

Description

Output Off

Output On

DO1 Compressor

#2

Compressor Off

Compressor On

DO2 Compressor

#4

Compressor Off

Compressor On

DO3 Compressor

#6

Compressor Off

Compressor On

DO5

Circuit 2 Hot Gas Bypass SV

Solenoid Closed

Solenoid Open

DO6

Circuit 2 Liquid Line SV

Solenoid Closed

Solenoid Open

EXV Module 1 and 2

These modules will be used only when the expansion valve type is electronic.

Digital Outputs

Description

Output Off

Output On

DO1 Circuit 1 Fan Output 5

Fan(s) Off

Fan(s) On

Stepper Motor Output

Description

M1+, M1-

EXV Stepper Coil 1

M2+, M2-

EXV Stepper Coil 2

Sensor Information

Temperature

All temperature sensors will be McQuay part number 1934146.

Pressure

Pressure inputs will be read using 0 to 5 volt ratiometric sensors. Nominal voltage range will be 0.5 to
4.5 volts.
Pressure on the low side will be measured using McQuay part number 331764501.
Pressure on the high side will be measured using McQuay part number 331764601.

Actuator Information



The electronic expansion valves used are McQuay part number 33038620X. These valves are

Sporlan supplied and all use the same bipolar stepper motor.

Setpoints

Setpoints are stored in permanent memory.

SetPoint Tables

Setpoints are initially set to the values in the

Default

column, and can be adjusted to any value in the

Range

column.

«
...
14
15
16
17
18
...
»

Содержание McQuay AGZ-D



















































































Отзывы:

Нет отзывов