Daikin Magnitude Скачать руководство пользователя страница 6

Страница: 6 / 70

IOM 1210-7 • MAGNITUDE

MODEL WMC CHILLERS

www.DaikinApplied.com

nTroduCTIon

General Description

Daikin Magnitude

Centrifugal Chillers are complete, self-

contained, automatically controlled, liquid-chilling units

featuring oil-free, magnetic bearing compressors. All

Magnitude

chillers are equipped with a single evaporator and

a single condenser along with either one or two compressors

depending on the model. TMC Templifier units are equipped

with centrifugal compressors and are available as a

configuration, each with optional pass arrangements.
Magnitude

chillers are designed for indoor, non-freezing

installation only. The chillers use refrigerant HFC-134a that

operates at a positive pressure over the entire operation range,

so no purge system is required.

Only normal field connections such as water piping, relief valve

piping, electric power, and control interlocks are required,

thereby simplifying installation and increasing reliability.

Necessary equipment protection and operating controls are

included.
All Daikin Applied centrifugal chillers must be commissioned by

a factory-trained Daikin Applied service technician. Failure to

follow this startup procedure can affect the equipment warranty.
The standard limited warranty on this equipment covers parts

that prove defective in material or workmanship. Specific

details of this warranty can be found in the warranty statement

furnished with the equipment.

NOMENCLATURE

W M C 043 D DS

Figure 1: WMC-D Major Component Locations

NOTE:

Unit shown with right-hand water connections and optional economizer. Water connection orientation is based on facing

the unit power panel.

W = Water-Cooled

T= Templifier

Magnetic Bearings

Centrifugal Compressor

Vintage/Single Circuit

D = Dual Compressors
S = Single Compressor

Impeller Code

Condenser Vessel

Evaporator Vessel

Power Panel

Compressor #2

Compressor #1

Human Machine Interface

(HMI)

Control Panel

Tube Sheet

Economizer

Содержание Magnitude







































































Результаты поиска

Содержание Magnitude

Отзывы:

Похожие инструкции для Magnitude

Бренды по названию

Популярные бренды

Daikin Magnitude, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnitude

Отзывы:

Похожие инструкции для Magnitude

Бренды по названию

Популярные бренды