Daikin LRMEQ4BY1 Скачать руководство пользователя страница 40

14 About the system

Installer and user reference guide

40

LRMEQ+4BY1

Air-cooled refrigeration condensing unit

4P500362-1A – 2018.09

For the user

14

About the system

NOTICE

For future modifications or expansions of your system:

A  full  overview  of  allowable  combinations  (for  future
system  extensions)  is  available  in  technical  engineering
data  and  should  be  consulted.  Contact  your  installer  to
receive more information and professional advice.

14.1

System layout

c

b

d

a

a

Outdoor unit (ZEAS condensing unit)

b

Refrigerant piping

c

Indoor unit (Blower coil)

d

Indoor unit (Showcase)

15

Before operation

WARNING

This unit contains electrical and hot parts.

WARNING

Before operating the unit, be sure the installation has been
carried out correctly by an installer.

NOTICE

Never  inspect  or  service  the  unit  by  yourself.  Ask  a
qualified service person to perform this work.

CAUTION

It is not good for your health to expose your body to the air
flow for a long time.

CAUTION

To  avoid  oxygen  deficiency,  ventilate  the  room  sufficiently
if equipment with burner is used together with the system.

CAUTION

Do  NOT  operate  the  system  when  using  a  room
fumigation-type  insecticide.  Chemicals  could  collect  in  the
unit,  and  endanger  the  health  of  people  who  are
hypersensitive to chemicals.

NOTICE

Be  sure  to  turn  on  the  power  6  hours  before  operation  in
order  to  have  power  running  to  the  crankcase  heater  and
to protect the compressor.

16

Operation

16.1

Operation range

Use  the  system  in  the  following  temperature  ranges  for  safe  and
effective operation.

LRMEQ*

LRLEQ*

Outdoor temperature

–20~43°C DB

Evaporating temperature

–20~5°C

–45~–20°C

16.2

Operating the system

16.2.1

About operating the system

▪ To  start  and  stop  operation  of  the  outdoor  unit,  use  the  external

operation switch.

▪ If the main power supply is turned off during operation, operation

will restart automatically after the power turns back on again.

17

Energy saving and optimum
operation

▪ Turn off the main power supply switch to the unit when the unit is

NOT  used  for  longer  periods  of  time.  If  the  main  power  supply
switch  is  on,  the  unit  consumes  electricity.  Before  restarting  the
unit,  turn  on  the  main  power  supply  switch  6  hours  before
operation to ensure smooth running.

18

Maintenance and service

NOTICE

Never  inspect  or  service  the  unit  by  yourself.  Ask  a
qualified service person to perform this work.

WARNING

Never replace a fuse with a fuse of a wrong ampere ratings
or  other  wires  when  a  fuse  blows  out.  Use  of  wire  or
copper wire may cause the unit to break down or cause a
fire.

CAUTION

Do  NOT  insert  fingers,  rods  or  other  objects  into  the  air
inlet  or  outlet.  Do  NOT  remove  the  fan  guard.  When  the
fan is rotating at high speed, it will cause injury.

CAUTION: Pay attention to the fan!

It is dangerous to inspect the unit while the fan is running.

Be  sure  to  turn  off  the  main  switch  before  executing  any
maintenance task.

CAUTION

After  a  long  use,  check  the  unit  stand  and  fitting  for
damage. If damaged, the unit may fall and result in injury.

Содержание LRMEQ4BY1













































Отзывы: