Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 301

Страница: 301 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

300

14-3 Error Information Function

When an error occurs, the management point where the error occurred can be checked from the

group monitoring icon indicating error displayed on the Standard View screen.

When an error is detected, it is notified by a flashing

(Red)

(Yellow)

, and displaying a balloon. If

set up, the buzzer will also sound.

(Red)

Flashing: System error

Text: System error occurred. Touch this icon to check and restore.

(Yellow)

Flashing: Unit/Limit Error

Text: Error occurred. Touch this icon to check.

(Blue)

ON: Communication error

* Neither will the buzzer sound nor a message appear.

Touching the icon displays the Error Information dialog.

Touching the icon when privilege restriction is set up displays the Password Input dialog.

Entering the correct password displays the Error Information dialog.

NOTE

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды