Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 225

Страница: 225 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

224

Select the

Month

radio button

(b)

to set the Account Date. The data collection period is determined

as the month from the Account Date of the previous month.

For example, if the date on the iTM unit is October 20th, and Account Date is set to the 20th, then

proportional distribution is calculated for the period from September 20th to October 19th.

Touch the Modify button and enter the Account Date. You can enter a value in the 1 to 31 range.

However, if the specified counting date does not exist in the month, the counting period will be

automatically adjusted to match the calendar dates.

(2)

is the button for making advanced settings that are normally unused.

Collecting data and outputting the Power Proportional Distribution results

(4)

(3)

Touching the

Execute

button

(3)

displays a confirmation dialog. Connect the USB memory to the

iTM unit and touch the Yes button to start data collection and CSV file output.

Data collection may take up to 30 minutes. When data collection finishes, a list of the periods and

results of the data collection appears in

(4)

If the USB memory is not connected, data is collected and the collection results displayed but no

file is output.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды