Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 167

Страница: 167 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

166

Detailed screen and button descriptions

•

Main Interlocking Control Screen

This screen is displayed when you touch the Interlocking Control button on the Automatic Ctrl.

tab of the Menu List screen (see page 52).

This screen allows you to create and delete interlocking programs, as well as enable/disable the

interlocking programs.

(8)

(1)

(3)
(4)
(5)
(6)
(7)

(2)

(1)

Interlocking program

list

Displays registered interlocking programs.

(2)

Enable/Disable

radio button

Enables and disables an interlocking program.

(3)

Create

button

Creates a new interlocking program. Touching the button displays the Name Input dialog.

The maximum number of interlocking programs you can create is 500.

Set up a name using 1 to 32 characters, irrespective of single or double byte.

Duplicate names are not permitted.

(4)

Copy

button

Copies the program selected in the interlocking program list. Touching the button displays the

Name Input dialog.

(5)

Delete

button

Deletes the program selected in the interlocking program list. Touching the button displays a

deletion confirmation dialog.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды