Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 159

Страница: 159 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

158

Setting up an interlocking program

The following describes how to program and set up an interlocking program based on the model

case below.

•

Turn On the Ventilator when any of the indoor units for Office B goes On.

•

Turn Off the Ventilator when all indoor units for Office B go Off.

Interlocking program name:

Ventilator control program

Target:

Office B (area consisting of indoor unit “a”, indoor unit “b”, and Ventilator “c”)

Control program:

(Output1)

When either indoor unit “a” or indoor unit “b” goes on, turn on Ventilator “c”.

The required duration is “10 minutes”.

(Output2)

When both indoor unit “a” and indoor unit “b” go off, turn off Ventilator “c”.

•

Creating the Interlocking Program

Touch the Interlocking Control button on the Automatic Ctrl. tab of the Menu List screen and

display the main Interlocking Control screen (see page 52).

(1)

(2)

1. Setting up the interlocking program name

Touch the

Create

button

(1)

and enter the program name in the Name Input dialog that appears.

Enter

“Ventilator control program”

Select the

“Ventilator control program”

registered in the list and touch the

Edit

button

(2)

display the Interlock Program Setup screen.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды