Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 138

Страница: 138 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

137

7-2 Outputting Function Settings

The iTM includes various functions, and each of them needs settings. You can output them to a

CSV file using the batch settings output function and load it to a computer to check the current

values in a list. The following describes how to output the settings.

See below for settings you can output using this function.

<Batch settings output details>
For information on how to interpret the output file, see the tables on the next pages.

Function

Output content

Schedule

Settings of programs registered with the Schedule Control.

Interlocking Control

Settings of programs registered with the Interlocking Control.

Emergency Stop

Settings of programs registered with the Emergency Stop.

Auto Changeover

Settings of programs registered with the Auto Changeover.

Temperature Limit

Settings of groups registered with the Temperature Limit.

Sliding Temperature

Settings of groups registered with Sliding Temperature.

HMO

Settings of management points registered with HMO.

Setback

Recovery temperature and setback temperature settings.

Power Proportional
Distribution

Excluded time settings of the past 13 months.

1. Touch the Setup Export button on the Operation Mgmt. tab of the Menu List screen (see page

56).

2. A confirmation dialog with the message “Save CSV-file with batch output settings?” appears.

Connect a USB memory to the iTM unit and touch the Yes button. Outputting to the USB

memory takes up to 2 minutes per 1MB.

3. Output is complete when the message “File has been saved.” appears. Touch the Close button

to close the screen.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды