Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 130

Страница: 130 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

129

6-7 Setting up and Changing the Screensaver

You can set up or change the screensaver, as well as set up or change the setting for turning the

screen off.

1. Touch the Screensaver button on the System Settings tab of the Menu List screen and display

the Screensaver Settings screen (see page 54).

(4)

(1)

(2)

(3)

2. Enable/disable and set up the screensaver type using the

Screensaver Method

(1)

combo box.

Select from Disable, Backlight Off, Screen1, Screen2, and Screen3. Selecting Backlight Off will

turn off the screen when the idle time set in step 3 elapses.

Touch the

Preview

button

(2)

to preview the selected screensaver. Touch the screen to return to

the Screensaver screen.

3. Touch the

Modify

button

(3)

and enter the idle time until displaying the screensaver or turning

off the screen. You can specify an idle time of 1 to 60 minutes.

To automatically stop the screensaver, sound the buzzer, and display the Error Notification icon

when an error occurs while the screensaver is being displayed or when the emergency stop

occurred, select the

Screensaver Off when Error occurs

radio button

(4)

To continue displaying the screensaver, select Disable.

5. Touch the OK button to save and close the screen.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды